Find experienced local tradies in Melbourne

Hi all – please read the job in full before accepting. I’m looking for a plasterer tomorrow to patch and paint 4 holes following the installation of new lights. Job requirements: * Patch all 4 holes * Sand and finish neatly * Colour-match and paint the repaired areas * 3 holes are on the left side, including one in the ceiling/roof area which may require a ladder * 1 hole is on the right side, above the bed * Please see photos for the exact locations and condition Access & parking: * The property is an Airbnb in the Melbourne CBD * There is no free parking available, so please factor parking costs and the inconvenience of CBD parking into your quoted price * Keys will need to be collected and returned to a convenience store approximately 5 minutes’ walk from the property * The convenience store opens at 9:00am * Full access and key collection details will be provided ahead of the job Please only accept/quote if you’re confident working solo and you can complete both the plaster repairs and painting tomorrow or by lunchtime Friday. Thanks!

I’m looking for a licensed electrician to install one new double power point on a plasterboard wall in my apartment. There is an existing double power point approximately a few metres away near the marble shelf, which I’d like the new outlet to potentially be supplied from. The job: * Install 1 x standard double GPO underneath the existing picture frame (see photo). * Ideally run the cable inside the plasterboard wall cavity from the existing power point. * I want no visible cabling or plaster chasing between the two points. * Only the necessary cut-out for the new GPO. * Please assess whether the existing GPO/circuit is suitable for the additional outlet. * Supply and install the GPO. * Test and leave the installation compliant and tidy. * Licensed electrician only – Victorian electrical regulations apply. Budget: $250–$300 Seeking a fixed price agreed before starting. Please quote including labour, materials and installation and confirm you are a licensed electrician in Victoria. Photo attached showing the existing socket and proposed location

6 x gpo to be connected on newly installed skirting boards . Holes have been cut out.must be licensed electrician.cab be done today or tomorrow.

Its a motor and remote operated Awning and extends full. It just needs to be realigned and adjusted to the correct position as one side is tilted downword and its low on full extension. Pleaes quote. Thanks

New sheeting applied - basic stopping of screw holes and a small hole of area 4 x 2 m

After a renovation a couple of years ago, we altered the balustrades to accommodate a new nib wall. Since then they have been unstable and recently a section of the balustrades collapsed and need to be securely reinstated. I haven't measured the affected area but I think it's 1.5-2 metres long. All the existing balustrades are in tact so replacements pieces are not required.

100 x 200mm render and paint. Client has correct paint on site.

Need help finishing a room. Probably 1-2 days work. Willl be working with me per day

Elfa top track shelving system. Task is to attach two top tracks high up on a wall 3m wide. Four metal studs will be used and the rest into the drywall itself. All screws and wall anchors available. Same with drill machine and drill bits. Stud finder as well. Short 60cm physical leveler exists but would be ideal with a laser

I need holes in the wall fixed from a tv bracket in two bedrooms

Experienced plasterer needed in Brunswick East for a kitchen bulkhead and related finishing work, plus an under-stairs cupboard. Kitchen * Build, sheet and plaster a new bulkhead above the overhead cabinetry. * Approx. 2.1 m wide x 325 mm high from ceiling to cabinet top. Final measurements to be checked on site. * Depth to align neatly with the front of the upper cabinetry. * Create a clean shadow-line/recessed finish above the cabinetry. * Install matching cornice across the new bulkhead and tie into the existing cornice. * At the tall fridge cabinetry, finish the nib wall neatly and return the cornice along the hallway side so it terminates cleanly at the nib wall, rather than wrapping around the short end. * Finish the short end of the nib wall flush and clean beside the fridge cabinetry, including the top junction shown in the photos. * Close and plaster the narrow gap between the island counter frame and services column (about 3cm x 90cm) * Finish exposed corners/edges, including corner bead, stopping and sanding where required. * Caulk/seal small gaps at plaster-to-cabinetry, cornice and wall junctions. * Leave ready for painting. Under-stairs cupboard * Complete/tidy existing plasterboard inside the cupboard, including the low sloping underside of the stairs. * Main unfinished wall area is roughly 1.2 m x 2 m or less. * Sheet over remaining exposed wall/framing. * Tape and stop joins, corners and screw holes. * Tidy rough/unfinished sections shown in photos. * Caulk small gaps where required. * Sand and leave ready for painting. Photos show the current condition and intended works. Job may require more than one visit for setting/drying between coats. Please quote for the full job and advise if materials are included. Painting not required.

Removed splashback tiles from kitchen and 1 layer of plasterboard came off with it (see pictures). Need new plasterboard installed by qualified tradesperson. Approx 5m x 0.6m plasterboard required. Must be ready for splashback tiling after. Needs to happen before kitchen installation Monday 31 August.

Looking for an experienced trade painter to repaint the exterior architectural trims, gables, and fascias of a single-storey weatherboard home in Thornbury (see attached photos). Scope of Work: Front Facade: Paint front gable trims/battens, window awning/hood, timber window frames/sills, and lower plinth baseboards in a heritage muted olive green (per mockup image). Rear Facade: Paint rear roofline fascias, gable cladding/trims, window/sliding door perimeter trims, and lower baseboards. Side Laneway/Path: Paint metal/timber fascias, gutters, downpipes (changing over from burgundy), and lower baseboards along the side pathway. Prep Work: Light sanding, cleaning down surfaces, scraping loose paint, and spot priming where required. Materials & Requirements: Paint (Supplied by Painter): Painter to supply premium exterior acrylic paint (e.g., Dulux Weathershield or Taubmans All Weather) tinted to agreed olive/green trim colour (e.g., / Olive Leaf). Equipment: Painter to supply all brushes, rollers, masking, drop sheets, and ladders/step platforms. Access: Flat, clear ground access at front, rear, and side brick pathway. Please state your experience with exterior timber and metal trim painting and include links/photos of past work when submitting your offer.

We have a hole in our plasterboard in the kitchen that needs to be fixed/patched. The area to be patched is approximately 10cm x 10cm.

Looking for an experienced plasterer to do a professional skim coat, fill gaps, and give smooth finish on newly installed gyprock." "Job is ready now, flexible with timing.

We’re moving out of our South Yarra apartment and want to get it inspection-ready to secure our bond back. Looking for a general handyman to come give the place a once-over and patch up minor marks and damage before our final inspection. What we need: • Walk through the apartment and touch up scuffs, marks and small dents on walls and ceilings (paint colour matching where needed) • Fill and patch a few small gouges/chips (wall corner, architrave, wall dents) • Supply and fit a cover plate for a double power point that’s missing its faceplate • If possible, repair a small chip in a floor tile — happy for you to take a look, but not a dealbreaker if it can’t be done Please bring your own filler, paint/touch-up supplies and a standard power point cover. If you need us to confirm the paint colour or socket brand beforehand, just message us. Melbourne / South Yarra. Flexible on timing except for Monday as the cleaners will be there — let us know your availability and quote. Thanks!

Had a new vanity installed and require either a render or tiling completed. Jist getting ideas on both options.

Looking for a licensed electrician to complete the electrical work required for a new heat-pump hot-water system being installed ( new double power point) Hot water system: Midea RSJ-23/300RDN7-L2 280L heat-pump hot-water system with electric element. Job details: • New Midea unit will replace the existing Aquamax gas hot-water system shown in the photos. • A suitable weatherproof outdoor Double power point/electrical connection is required for the new Midea unit. • There is already an external power point supplying the ducted heating approximately 2–3 metres away. • Good access underneath the house via the subfloor. • Photo of the existing switchboard is attached. • Electrician to determine whether an existing circuit can safely and compliantly be used/extended, or whether a new dedicated circuit/RCBO is required for this particular Midea unit. Please quote your best ALL-INCLUSIVE price for everything electrically required to have the Midea ready for connection, including labour, weatherproof power point, cabling, circuit/RCBO if required, materials and electrical compliance/safety certificate. Please base your offer on the information and photos provided and advise in your offer exactly what is included. Must be completed by a licensed electrician and fully compliant. Thankyou 😊👍

Build Alpine 1 person Sauna. It's a clip lock together and say 1-2 hours on instructions https://alpinespas.com.au/saunas/infrared/oslo-1-2-person-indoor-infrared-sauna-gen2

I need some help with a few small jobs: • Repair the plaster where I removed a bathroom mirror. • Apply silicone to seal the gap between the vanity splashback tiles and the wall, where the mirror once covered • Repair a hole in the plaster caused by the front door handle. Please note that I do not require painting - just plaster board repair.