Find experienced local tradies in Richmond VIC

Need a beam replaced that is rotting on my Verandah. Photos attached.

Driving out of the garage our car scraped off some of the corner of our house concrete rendering. There’s one longer spot approx Approx 13cm long + one smaller spot approx 3cm long above that. See pictures. We’d like someone to put the corner back and match the colour as close as possible so it blends in. Thank you!

A few holes to fill up and render the surface

I have some slab edges as shown that have been defected for not being clean enough. I need a renderer to come through and skim patch areas with a cement based product like panel patch or render roc to match into the slab edge. Price is for an hourly rate materials can be charged additionally. Approx 100 lm at a height of 400mm . One coat to clean the edge is all thats wanted. Its just a slight clean up for the edge of a concrete slab thats not really going to be looked at.

The window pane is fine, but the rotating lever is getting stuck and doesn't completely close the window. I think the chain that pushes it out, and closes it might be the issue.

I need help mounting a Samsung 65" Frame TV on my lounge room wall. The wall is gyprock over double brick. I'd like to conceal the cable if possible behind the wall but I'm not sure if sufficient clearance is available between the gyprock and brick. Can you please quote me for: (1) just mounting the TV on the wall - requires mounting the Samsung slim-fit bracket into masonry, levelling, etc: please provide best quote up to $200; and (2) concealment of cable (if possible) - quote on site. If you can't give a quote for item 2 until you are on site that's fine, let me know how much 1 would be and an estimated cost range for 2 depending on whatever factors you think are relevant. Thanks!

Hello. I’m after someone to re render two small walls. Both are less than 5m long and 1m tall. There’s a very thin layer of render currently on them.

Exit light changed to a new light and separate switch. Also need power point moved up behind TV

Need someone to assist with wall plastering base coat + top coat in 4 areas as shown in the photos

Replace the arm of a commercial awning. I was about to assign the task but ad has expired.

I’m looking for someone to prepare and plaster areas of several walls and the ceiling in my 1 bedroom apartment. The task also includes filling and siliconing new skirting boards throughout the entire apartment to get everything ready for painting. I'm flexible with scheduling and it's not urgent. Feel free to reach out if photos are not clear and you need to view job before quoting.

Hoping to get someone to build this sauna for me

*Resubimtted due to Airtasker cancelling on me* I need x2 movable walls sheeted with gib and plaster to finish. Only need the labour done, all materials will be provided. You will need your own tools. Walls - Height is 2200mm Walls - length is 4400mm Walls Depth - 50mm See pics for frames. The pics only show 2200 length frames as an example…the ones I need done will be twice as long. Each frame will need 8 sheets attached to complete and plastered. Can do the Job from Thursday 4th September.

Electric awning, remote controlled. One arm snapped yesterday. Replacing both arms is too expensive. Looking for solutions.

I need an experienced tradesman to do a simple site set out for concretors using pegs and a laser. I've recently had eye surgery and need someone to step in. I have rotary and stabilia multi line set out laser, star pickets and timbers. I also need a few RL's shot and marked. Please see plans attached.

Install a power point above an existing one in Richmond Vic

Renderer required for external brick walls. Easy access. See photos. Located Richmond

I need some rendering repair done on my house. Some is on level 2 so may require small scaffold/tall ladder. Need good job that doesn’t cost the earth You may need to come and do a quote

I need a plasterer to trowel up an internal wall that was cut into to replace an air conditioner.

take apart a sauna and re-assemble a 2 man luxo sinfrared auna