Find experienced local tradies in Sydney

Have removed tiles from a shower recess and need the wall rerendered to prepare for the new tiles.

Hi, See attached pics of ceiling where I want approximately 11 warm white smart LED lights installed in pic 2 power point moved and a power point pic 3 moved with bedroom light switch , its a gyprock ceiling with concrete walls Must have dimmers about 3 and like the feature where i could change the colors like smart LED .I can assist if needed too. Thanks :-)

two areas of 9 m2 each . T fix gyprock pieces around edges of full sheets, plaster all and sand all. Gyprock sheet material at premises.

Rendering of Cavity Flashings, Rendering of Slab Edge and Rendering a Block Wall

I need to relocate a power point and a light switch in my study. I’m getting some cabinetry put in the 30th November and need to move things around a little bit. There is a telephone line plug that I would just like to be taken off the wall, no need to relocate to other wall as not needed

Looking for someone to: - remove the gyprock partition and architrave as pictured (waste can be left on site) - patch the rear wall as required where the partition was, and sand ready for painting (do not need to paint) - patch the ceiling where the exhaust fan is and sand ready for painting (do not need to paint) - install new floor tiles where the partition was. Spare matching tiles supplied. This part of the room is not waterproofed. Waste can be left outside as a skip bin for other work will be ordered in a few weeks. Many thanks.

Need to do rendering around window opening to match existing one.

We need an experienced mirror/glass installer to cut and install 3 large mirrors at our physiotherapy clinic. Each mirror already has the Z-clip attached, but we do not have the wall-mount brackets, so you will need to supply and install the matching brackets. Mirror details: • 3 × mirrors — 3015mm × 709mm, approx. 5mm thick • Mirrors already onsite (no pickup needed) • Installed using Z clips – top clip load-bearing, lower clips to keep mirror flat • Manufacturer measurements for clip heights and spacing provided Installation surfaces: • 1 × brick section • 2 × gyprock sections Installer must supply correct fixings for both. Scope of work: • Supply matching Z-clip wall brackets • Measure and cut mirrors if required • Install brackets at correct heights • Hang all mirrors flush, level, and secure • Ensure minimal bowing using additional clips Manufacturer notes: • Mirrors sit 5mm off the floor • Clips #2 and #4 are non-load-bearing (prevent bowing) • Diagrams of clip positions available Location: Strength and Pilates Physiotherapy G 103 Foveaux Street, Surry Hills (ground floor) Requirements: • Experience installing large gym/studio mirrors • Own tools, brackets, fixings, adhesive if needed • Ability to cut mirror cleanly • Professional finish essential

Need 85 inch tv mounted to plasterboard wall tomorrow at 1pm

Hi, I’ve just demolished an internal wall and now need a gyprocker or plasterer to: • Patch and repair wall and ceiling gaps • Re-sheet and flush joins • Sand and prepare for painting There are some areas with exposed brick and framing that need neat finishing. I can send through photos for reference. Please let me know your availability, quote, and if you can come by this week for an inspection. Location: hillsdale

We need to have a 2.1m half wall plaster repaired at the edges and raised by about 5 cm, so it lines up with our kitchen cabinets for the upcoming stone benchtop installation

Jobs 1 and 2 are simple. Fill the holes with plaster and then paint over. Job 3 is more complex. Cut out the gyprock (may be fire rated gyprock, am not sure), replace-gyprock that square, plaster and paint. We will provide paint. Other materials provided by you.

ofter pulling a 3M sticker off the wall I removed the layers of paint - roughly 1 x 2 inches and two small pin holes need filling and painting

I need gyprock installed to the lower third of an exposed brick wall to prepare the wall for installation of wainscotting. The section of wall to be covered is 270*90cm You will need to include all materials in the quote.

I need an experienced person (or team) to carefully dismantle and reassemble a 3-person Found Space sauna and move it literally next door — about 20 steps away. The job needs to be done ASAP. Here’s what’s involved (essentially the reverse of this video: YouTube link): https://www.youtube.com/watch?v=jgsmWnB5Xfc Steps: • Remove the glass door first (must be done before anything else) • Disconnect all cables from the control box that run through wall cavities • Unscrew the roof • Unscrew and remove front heaters • Lift off the roof • Remove the glass panels • Disassemble the bench and under-bench heaters • Unscrew and separate the back panel You’ll then need to reassemble it in the adjacent room, ensuring it’s level, stable, and the electrical components are correctly reconnected. Requirements: • Must have experience assembling or moving infrared or similar saunas • Must have your own tools and basic electrical understanding • Ability to handle glass safely This is a quick but delicate job — ideal for someone who’s handy with furniture or appliance assembly and available immediately.

Put together a Serenity Full Sprectrum 2P sauna that came in a kit. Instructions on their website.

Job: Cut approx 1m (or less) Channel in Brick Wall + Install Conduit + Render Back to Smooth Finish Hey everyone Always had a good Airtasker experience Just had my TV hung on the wall I’d love an approx 1 metre vertical chase (channel) cut into an internal wall (brick) to run TV cables (sealed power/AV leads) from the floor up to a wall-mounted TV. Scope of Work: • Cut a neat 1m channel into brick wall (approx. 20–25mm wide, 20–25mm deep). • Supply and install PVC conduit for the wires • Secure conduit with saddles/clips inside channel. • Patch and render back over channel so the wall is flush and ready for paint. Happy to do the painting myself :-) • Finish should match existing wall as close as possible please (smooth render, not a lumpy patch job). I’m happy to handle final painting, I just need it rendered smooth and ready. Job Location : Surry Hills

Description: I need help installing a prefabricated outdoor awning (see attached diagram). The frame and materials are already on site and ready for assembly. Details: Awning type: Polycarbonate sheet with metal frame (see diagram for reference). Installation location: Above balcony/doorway (requires drilling into brick/concrete wall). Size: 2000 mm width, 7000 mm long Materials: All parts supplied. Task requires: Tools for drilling and fixing into wall Ladder or suitable access equipment Ensuring watertight and secure installation Other Notes: Please have relevant handyman/installation experience. Must bring your own tools and fixings if required. Flexible with time, but would prefer installation within one month. Budget: $400

Licensed Electrician Needed – Install Double Power Point (Behind TV) I need a licensed electrician to install a standard double power point (GPO) behind my wall-mounted TV in my apartment (Waterloo, NSW). • A junction box has already been installed to make it safe. • I would like this junction box replaced with a normal double power point, positioned neatly where the TV will be mounted. Requirements: • Licensed electrician (please provide license details). • Supply and install a standard white double power point. It will be supplied. • Ensure work complies with AS/NZS 3000 wiring standards. • Finish should be safe and neat. Plaster and painting will be done separately not including in the job. Location: Waterloo, NSW (apartment building). Parking available. Timing: Flexible

Bagging a rear wall around back sliding door, a little bit of filling in corner also. Price to include labour and materials. 7 square metres in total