Find experienced local tradies in Castle Hill NSW

Install Felt wall or build Gyprock wall for reception area

Looking for a local electrician to replace a ceiling light as below photo. The handyman said something may have burnt out inside so electrical work may be required. Also, seeking help to replace the 4 power points as bleow photo. Please let us know your availability. materials and labor cost with the quote. Thanks.

Hi, I have purchased the Alpine Copenhagen sauna, but it's a bit too bulky and heavy for me to put together. It looks easy, just clips in together, but the panels are maybe 40-60kg & around 120cm wide. Their video instructions say it takes an hour to put together & normal wall plug in set up. We have unpacked it from the crate and it needs to be lifted panel by panel up a couple stairs into the house, maybe 30m

An outside (under the rear verandah) single powerpoint fixed to the bottom of one of the verandah support posts. The power cabling will need to run up the post across to the house under verandah roof (about 1.5 metre span) all in conduit, then through the brick veneer wall and into the ceiling cavity (manhole is right there) and then join into the power supply.

I need an external powerpoint installed on a support post under the back verandah. The connection would be in the main dwelling ceiling above the laundry accessed about 4 meters away through the manhole in the laundry ceiling. The veranda attaches to the main dwelling. PowerPoint is for a water feature to be plugged into.

We’re renovating our kitchen and looking for an experienced handyman to complete the following works: * Demolition of entire kitchen, including pantry, and rubbish removal/disposal * Patch and repair plasterboard after demolition * Install/repair cornice where required * Plaster patching, filling and sanding to achieve a smooth finish The kitchen is approximately 3m x 4m and the house is single level with easy access – no stairs involved. We’re looking for someone who can complete the make-good works neatly and get the area ready for the new kitchen installation. Please provide a quote and let us know whether materials and rubbish removal/disposal are included.

I need an experienced plasterer/handyperson to repair an impact-damaged section of an internal Gyprock wall. The damaged area is approximately 30 cm × 22 cm. A soccer ball hit the wall, causing the Gyprock to crack and lift. There is a brick wall behind the Gyprock. The job should include: * Remove all loose and damaged Gyprock * Inspect whether the surrounding board is still securely attached * Cut and install a suitable plasterboard patch if required * Add backing/support behind the patch as needed * Tape and apply joint compound to all joins * Apply finishing coats and sand the area smooth * Prime the repaired section * Paint the repaired area to blend with the existing wall * Clean up and remove repair waste Please provide all required materials and tools. I can provide photos of the damage. Please confirm whether your quote includes materials, primer and paint. The wall paint will need to be colour matched. Please include your experience with plasterboard repairs, availability and total quote.

Plaster hole , fix drop in ceiling and gap between roof and cupboard in kitchen

Stair balustrade to be painted (light sand, primer, gloss white x 2 coates). Perspex will be removed

I need to get some gyprock work done around my house. Work includes: 1. Patching all electricians cutouts (around 25) 2. Patching all carpenters cutouts (2 total) 3. Fixing one corner of a wall (photo attached) 4. Fixing existing gyprock on two walls. (Photos attached) All quotes must include sanding as well, no painting required as I will repaint the entire house.

Hi, I need a gyprock hole wall repaired. 1. Hole size is approximately 35–40 cm (see attached photo). 2. Supply and install a gyprock patch. 3. Plaster, sand, and make the wall smooth. 4. Apply primer and match the existing white paint on the repaired area. Please send your quote and availability.

I am replacing my old range hood. It needs to be installed on a gyprock wall which will need to have anchor to be put in place to hold the unit . Plus existing rectangular ducting needs to be replaced . I also have an additional task of adjusting the height of my oven and taking it up by 100mm

Need a licensed electrician to install 2 new double power points. The red X in the photo marks the locations for the new double power points. The red circles show the existing power point locations. Location: Castle Hill. Please let me know your price and availability. Thanks!

Need to Demolition of Gyprock and carpet. Installed wooden floor and Automatic door

Looking for an experienced Harvia sauna technician to inspect and troubleshoot my home sauna. I am unable to remotely switch the sauna on/off via the Harvia Xenio WiFi control system. The sauna appears installed and operational, but the remote control functionality on the app is not working as expected. Sauna Details: Harvia Legend Tower PO70E Harvia Xenio CX170 WiFi External Control Panel Installed on a Luma Comfort 225 Thermo Barrel Sauna

Acrylic render 4 different areas . Walls and top of wall . Colour acrylic render . Job is ready to go . $6000 inc gst supply install and don’t leave a mess .

Outdoor garden retaking walls . Need rendering to 4 different walls

Need a gyprocker to patch a hole in my wall. Does not need to be painted (we will paint it later). Just ready for painting. Approx size 1m x 0.5m

We have some windows where old security bars have been removed, but metal bolts/brackets are still embedded in the exterior wall (see photos). There are approximately 4-6 fixings per window (around 30 total). Scope of work: * Cut/grind off remaining metal bolts/brackets (they cannot be removed easily with a screwdriver or drill) * Ensure they are cut flush with the wall surface * Patch all holes properly * Re-render/finish the surface to match the existing wall as closely as possible * Clean up after work Wall type: Rendered exterior wall (cement/render finish) Tools required: * Angle grinder or similar cutting tool (to cut metal) * Materials for patching and rendering Location: Castle Hill NSW Timing: Flexible, but preferably ASAP Please bring your own tools and materials. Experience with render repair / exterior patching is preferred. Photos attached for reference.

The wall was hit and had a piece broken. The broken part is about 10 cm. The offer should include labour and materials.