Find experienced local tradies in Cherrybrook

We are completing a bedroom renovation using IKEA wardrobes to create a built-in look. All IKEA wardrobe units, doors and accessories have already been purchased and are on-site. One side of the wardrobes has been installed, but the plasterboard finishing and painting are incomplete. The other side still needs wardrobe installation and finishing. The remaining work includes: * Assembling and installing the remaining IKEA wardrobes * Completing plasterboard work around the wardrobes and ceiling * Patching, plastering and sanding * Painting the repaired walls and ceiling * Finishing the edges and gaps for a seamless built-in appearance Please see the attached photos. Looking for an experienced tradesperson to complete the remaining work. Please provide a quote including labour, any additional finishing materials required, and an estimated completion timeframe. Thank you!

Have a hole in the gyprock ceiling in the kitchen and need the hole repaired, and painted.

Carpenter for the gyprock work (bulk head) around a pipe. and a skirting boards at the bottom for a finish and paint it.

Please see the attached pics. the plumbling pipe needs to be patched with gyprock around it. bulkhead work.

- Location: Cherrybrook, street parking or can park on my driveway easy. - Time: Work is urgent, need to be completed this week. - Work required: Need an experienced plasterer gyprocker to remove and replace failing cornice in bathrooms. Wall tiles are floor to ceiling so the cornice needs to bind to wall tiles. Needs to be a clean finish, reading for painting. Need all rubbish removed - Cornice size: About 90mm - Cornice length: • Main bathroom: 3.4m x 1.8m = About 10m • Downstairs bathroom = About 2m • Ensuite: 2.8m x 1.3m = About 9m

1. Internet to me moved from level 1 to ground floor. 2. Installation of TV in pergola. 3. Two new power points in pergola

Hi, I am looking for a licensed electrician to perform a minor electrical upgrade at my residential property in preparation for an EV charger. Scope of work: 1. Replace an existing 20A single-pole MCB (pure circuit breaker) with a new 20A Clipsal MAX9 Slim RCBO (Type A, 30mA, C Curve, 1P+N). 2. The electrician will need to locate the dedicated neutral wire for this garage/laundry circuit from the main neutral bar and correctly wire it into the new RCBO. 3. Replace the existing standard 10A double power point in the garage with a 15A single power point. 4. Run a delicate 2.5mm tps line from power board to garage power point, about 20-25metres. Materials provided by me: - 1 x Clipsal MAX9 20A Slim RCBO (MX9R3120) - 1 x Clipsal Iconic 15A Single Power Point Outlet What you need to provide: - Your own professional tools, testing equipment, and any minor consumables (e.g., a short length of neutral wire for the RCBO line input if needed). - Must provide an Electrical Safety Certificate (CCEW) upon completion. Requirements: - Must be a fully Licensed Electrician in NSW. Please provide your license number when making an offer. - Excellent reviews on Airtasker for electrical work. Photos of the current switchboard, the existing line (2.5mm² TPS), and the new materials can be provided upon request. Looking forward to your offers. Thanks!

Few holes in gyprock walls to be repaired . One large hole and few small ones

Need a gyprocker to sand, patch and paint around the ceiling vent area. The plaster around the diffuser is uneven and still visible from previous works, so it needs to be made good and repainted to match the ceiling.

Looking for an experienced handyman or plasterer to repair multiple areas of gyprock wall damage caused during a recent conduit installation. What I need: * Inspect and assess full extent of damage * Repair and patch all affected areas * Reinforce weak sections if needed * Sand and leave ready for painting (painting not required unless discussed)

Looking to install 2 power points in garage and a LED light

Gyprock done on both side of the wall please the photos and some patch work as well

I need all the walls to have a flat rendered finish And the floor screed done ready for tiles.

Looking for a licensed electrician (preferably with ABN) to install a power point underneath my stove so the gas stove ignitor can be plugged in and start working. Currently the ignitor isn’t working as there is no power outlet in that space. 3 photos attached to show the setup and help understand the job. Please quote if you: Are a certified/licensed electrician Have an ABN and can provide an invoice Can bring the required materials for installation

Patch gyprock holes in ceiling and wall

A section of my garage ceiling plasterboard has come loose and is sagging on the left side above the roller door. It looks like the plasterboard sheet has separated from the ceiling joists and needs to be re-secured properly with new screws. The cornice has also partially detached and may need re-gluing or replacing.

The aquacheck plasterboard is sagging from the corner. Need to get it fixed.

Hi, I’m looking for an experienced plasterer/handyman to help close and patch a gyprock wall 2.2m Height * 1.47m Wide

Require sanding back over previous plastering that was not sanded and then painted over which is unsightly. It was to go over light cracks in ceiling. Also require a piece of sagging cornice to replaced and painted

The pyramid shaped gyprock ceiling comes out once we change the Roof Rafters in the Roof space the ceiling goes back up and finally sand and paint. NB- The mobile scaffolding will be in place for the work to be undertaken