Find an experienced handyman in Fitzroy VIC

Has to fix the rotisserie flaps

Building EasyShed, details in link. And anchor to timber fence. https://easyshed.com.au/products/narrow-slider-garden-shed-3m-w-x-0-78m-d-classic

Please see the picture I need to fix the door

Need help to: - Put together an Ikea bookcase - mount 2 x wall heaters - mount large painting, hooks are on side of frame Pls see pictures

Need to get done: - Fit 1m of floor trim - Replace shower door lining on bottom of door (approx 0.75m wide) - Source and install a door knob (will pay for knob)

Install curtain rod upstairs for new curtains plus curtain rod downstairs. Hang a heavy round mirror. Hang a lightweight hat rack. Install brackets for lightweight light to sit on. Install brackets for shelving system. Help me move two lightweight desks from Collingwood to Fitzroy (studio to home) in your small van (5 minutes from studio to home).

- replace/fix the hinges for a double swing door Today till 5pm or tomorrow! Thank you

Attach some clothing racks (hung from the ceiling) for retail Pop-Up in Fitzroy. 6-7 racks total - made using steel poles from bunnings. All materials cost will be covered. Hung with metal cable that was attached to an elyelet in the ceiling and then wrapped tightly around the end of each pole - see photo from last store for reference of what it will look like. Installation needs to be Wednesday 13th in the afternoon / evening. Removal may also be needed on Wednesday 20th June 6pm - 9pm

Air conditioner unit emits a funny smell at beginning of cycle. Hoping to attain maintenance for this, likely needs pipe clean.

Need four brackets installed onto a brick so that we can hang two clothing racks - need to support a good amount of weight. Also looking for someone to install a hanging light. Ideally someone that can do both

Install door lock on bedroom door Lock supplied

Fly screen supply & installation to keep out insects, rodents, etc Retractable or permanent Dimensions: 220cm x 112cm

To quote on the following: We want to install a curtain rail along the bottom of our staircase to help block noise and contain heat. The ceiling is mostly plasterboard, with a steel pole in the middle. We are flexible about exactly where and how the rod could be installed. Additionally, we would like to patch up the two holes previous tradies left in the ceiling! Thanks.

Rebooking task between Pk and Ehsan

I’m looking for an experienced carpenter/cabinet maker to complete the final installation of two custom solid Tasmanian oak sliding wardrobe doors. This is a top-hung system (not bottom-rolling), so please read carefully. Overview - Qty: 2 sliding doors - Material: Solid Tasmanian oak (raw timber – no finishing required) - Size (each): 2510mm H x 1170mm W x 30mm T - Weight: Heavy solid timber What’s already done (~90% complete) - Top track is fully installed and fixed - Doors are already built to size - Opening/walls/floor are square - Flat timber floor (no slope) - Wardrobe carcass is complete Key clarification (important) This is a top-hung sliding door system with a low-profile floor guide, NOT a bottom roller/bottom track system. - Doors hang entirely from the existing top track - Bottom only needs a small guide to prevent lateral movement - Total clearance available: ~30mm (sufficient for this system) Bottom guide details - Low-profile plastic/nylon floor guide (shown in photos) Requires: - Routing a single narrow vertical groove into the bottom edge of each door - Fixing the guide to the floor - No bottom rollers, no full bottom track, no 50–80mm clearance required Scope of work - Route narrow groove in bottom of both doors - Supply & install suitable low-profile floor guide (or use supplied one if suitable) - Hang both doors on existing top track - Align/adjust so doors are plumb, stable, and slide smoothly - Install stops if required - Clean, professional finish Ideal person - Carpenter or cabinet maker - Experience with top-hung sliding doors - Confident routing grooves in solid timber - High attention to detail Photos provided: top track/hardware, floor guide, installation diagram, and wardrobe setup. Please quote including labour + any small hardware required. This should be a straightforward finishing job for someone experienced with this system.

Hole in the wall. About 10 by 15 cm

Hello, I need a handyman to do some cosmetic temporary repairs. Supply and cut to size a thin paintable ply / backing board 3-6mm to the area affected + paint in dulux natural white (supply). This is a temporary cosmetic fix. The temporary fix needs to be easily removable (screwed to plaster board) Carpet will be fixed by another trade. 1 metre ruler in photo for scale. Need to do complete works on January 2nd.

We have three current rods to hang from west elm, (see photos) in our Fitzroy rental (landlord approved) and would like it done before Christmas. Must have curtain hanging experience, thee robes are from west elm and will require someone who knows how to read an instruction manual as our last Airtasker had some trouble, and your own tools, ceiling is 2.8 meter so you will need a small ladder too.

Need a handyman to tighten our tap, put the shower screen back in place and remove some rubbish.

G’day, Looking for someone experienced and efficient to assemble / setup my 1.5m x 0.78m EasyShed Dog Kennel (EDK-1508) in Fitzroy as soon as possible. It is flat packed and according to the instructions requires a power drill, 3mm drill bit and a pop rivet gun. The area I would like it installed in is narrow against the side of the house on concrete pavers but it is measured to fit, just not a huge amount of room to spread out. I’m based in central Fitzroy with street parking and visitors permit available. Looking for someone to do this as soon as possible and by someone who is experienced with this kind of assembly. Once it’s assembled I will take care of fixing it to the ground / wall. Thanks, Ben.