Find trusted local electricians in Fitzroy VIC

Install 4 split system units

Change smoke alarm battery High ceiling so needs large ladder Need asap Roughly 4m high ceilings

The CCTV camera needs to record anyone coming onto my veranda. The NBN box is just inside the front wall of my house. I might decide to install two cameras fairly close together to get a back view and a front view of the person

I’m looking for a licensed electrician to replace five existing ceiling light fittings in small community yoga studio. Job details: * Replace 5 existing light fittings with new pendant/drop light fittings (supplied by me). * Ceiling height is approximately 4.2 metres, so you’ll need to bring a suitable tall ladder or other appropriate access equipment. * Please ensure all fittings are installed safely and tested before completion. * Studio will be empty during the job, so there will be plenty of room to work. Please include in your offer: * Confirmation that you’re a licensed electrician. * Whether you have suitable equipment to safely access a 4.2 m ceiling. * Your availability. Happy to answer any questions or provide photos of the existing fittings if needed.

I need an electrical spotter for 7-8 July 2026

The main wire is not connecting to the wire of oven

Looking for someone to: 1. Install an IKEA paper lantern pendant light above my dining table (all lamp components supplied). 2. Replace two bathroom light fittings (replacement lights already purchased and supplied). Shown in last pic The second photo shows how the previous tenant had the pendant lamp installed, which is the look I’d like to recreate. The existing ceiling setup and bathroom lights are shown in the photos. I’m unsure whether additional mounting hardware (hook/bracket) is required, so ideally someone can advise and supply any small extra hardware needed. Loft-style apartment with exposed beams. Please quote for labour and let me know if you are a licensed electrician.

White ceiling lights. Need to change them to warm. Not a bulb that I can replace

I need an old light fixture repaired in a rental flat. It's an old Batten Holder, I have a new B22 Batten Holder from bunnings I'd like to swap it out with.

Hi I’m after an electrician in Fitzroy area. The lights keep tripping the fuse box. All the other outlets are working fine. Thanks

To electrically spot while workman working

I have a wall panel that needs to be drilled into the wooden frame of my wall cavity that contains my hot water heater. I have the panel ready just need someone to reattach it with an electric drill and nails.

Replace light fitting - unit available

several need to be reattached or refitted..all are wired up..

Need four brackets installed onto a brick so that we can hang two clothing racks - need to support a good amount of weight. Also looking for someone to install a hanging light. Ideally someone that can do both

Looking for a licensed electrician for residential renovation rough-in work in Melbourne. Current condition: • Floor is already opened up, so access is available for underfloor cable runs • This is rough-in stage only, not final fit-off • Existing layout may be partly updated, so I want the cabling planned properly before closing floor / walls / ceiling Scope of works: 1. Site inspection and rough-in plan for key circuits 2. Run new cables where needed while floor is open 3. Rough-in for lights, switches and power points in affected areas 4. Rough-in for kitchen / bathroom / laundry power as needed 5. Check whether any dedicated circuits are required for appliances 6. Check condition of any existing wiring to be retained 7. Label new runs clearly where practical 8. Advise on any switchboard / safety upgrade issues if identified 9. Rough-in only for now; fit-off will be later after walls / floors are closed

Connect Coffee Machine to Electricity We need a qualified electrician to connect our coffee machine to power at our premises. Details: Coffee machine power requirements: Single-phase: 200–260 V AC, 50/60 Hz, 35 A Three-phase (optional): 380–400 V AC, 50/60 Hz, 22 A Total wattage: 6,300 W Brew tanks: 1.7 L, 600 W Steam tank: 12 L, 4,500 W I have attached a photo of the current switchboard for reference. Requirements: Must be a qualified/licensed electrician Ability to safely connect the machine to the correct power supply Advice on whether single-phase or three-phase connection is best is welcome Please contact me if you have any questions or need further details.

I have an old telstra wiring box I want it removed, but with the nbn cabling which is part of it reconnected after removal. In the photos you can see the conduit in, the conduit out as it goes through the wall (to the port) and the overall box

The tenants before loaded to many rooms onto one amp in the switch board, I need an electrician to move some of the load to another amp to spread out the load

Power point needs to be fixed to the wall. It is for a fridge.