Find an experienced handyman in North Melbourne

Hi there, I’m looking for a mobile panel beater or handyman to help smooth out a dent on my car(2023 Mazda cx5). The damage is on the front left fender and door edge, as shown in the photos attached. • No painting or full restoration required • Just want to make the surface look reasonably flat • Ideal if you have PDR (Paintless Dent Repair) experience or tools • Also a small crack on the plastic wheel arch – ok to glue or heat-repair Location north Melbourne Budget :$300-500

Get a quote to repair garage door

The blind chain in my bedroom has broken. I use a motorised driver so using joiners results in jams and further breakage. There is a very small gap between the blinds and the wall and I’m unsure of how to properly remove the blinds to change the cord. The distance between the top loop and driver is about 175cm. Ideally the tasker can provide a replacement metal chain as part of the service.

I have purchased a Flexi Storage Double Slot Wall Strip & Bracket system from Bunnings, and need someone to secure the brackets to a plasterboard wall. Consists of 3 x 1200 vertical brackets and 1 x 1200 horizontal hang track. Plasterboard screws provided, but would be handy if you have spares in case.

The board of the wardrobe door needs to be replaced and installed

Damage to internal walls due to roof leak Work required: Remove loose paint and plaster (bedroom walls and part of lounge wall) Repair hard plaster Repaint (colour "whisper White")

I need a Door Handle Replacement / Light Wood Filler Patch Up Job to clean up my Door, as the Door Handle has been ripped off completely & the Door itself is slightly damaged from where it was torn out.

There is a hole in the door I need fixed or replaced

Wanted: Chimney Stopper Installation for Mid-Century Home Looking for an experienced handyman, chimney specialist, or contractor to install a chimney stopper/cap in a mid-century house located in North Melb. Details: Single fireplace in use, original to the home Looking for a durable, weatherproof stopper (recommendations welcome) Access may require ladder or roof work Must be securely sealed to help with drafts and potential pests What we're looking for: Experience with older or mid-century chimney structures preferred Proper tools and safety equipment

New tenants are about to move in and a few things need fixing. Old TV wall mount to be removed, holes filled and wall painted (paint not supplied) Minor paint touch ups in apartment. Tighten sink tap. Fix gas cooktop knob (if possible). Fix hanging door stop. Tighten/fix pantry door handle. Fix toilet flush button. Re-secure splashback strip lighting. I'm flying over on Wednesday at lunch time, until Thursday afternoon.

Need to fix kitcgen cabinet. Came off as the wood is damp and the hinges came off. Need to install a plank of wood to fit the door in or a full change if thats required. Alao need to fix a drawer which came off from its hinges. Photos provided for more clarity.

I need the following installed professionally in my apartment in North Melbourne either thursday or friday this week: - 1 ikea Malmback shelf (https://www.ikea.com/au/en/p/malmbaeck-display-shelf-white-80446337/) - 1 small wooden shelf - 1 pegboard - 1 small door stopper - 1 vendline wall mounted laundry drying rack (https://vendline.com.au/products/wall-mounted-drying-rack-foldable-indoor-and-outdoor-drying-rack) I have the required parts and screws for all of these. My walls are drywall so you will need appropriate tools to install the items level.

Update: excluding supply of photo ledges and update task offer price. I like to install 2 photo ledges on my wall (115cm each), the area is close to my electrical box at home. I like to find someone who have a stud finder to avoid drilling into cables behind the wall. May I get a quote including the 2 ledges and materials. Will you be able to help? Many thanks. Ikea model: MOSSLANDA Picture ledge, white, 115 cm ($10 each) https://www.ikea.com/au/en/p/mosslanda-picture-ledge-white-70297465/?utm_source=google&utm_medium=surfaces&utm_campaign=shopping_feed&utm_content=free_google_shopping_clicks_Decoration&gad_source=1&gad_campaignid=17191453859&gclid=CjwKCAjw3rnCBhBxEiwArN0QE6enO9I9UuD5yC1ff3vAC745Zh3c2DQjJkuLZxlo4jBNQWXul_6NURoCCTIQAvD_BwE

Wall mounted pull up bar station installed on a brick wall. Requires masonary drill for 4 expansion bolts (provided). It is going to be fitted above a door so 2/3m high. https://shop.xinsports.com.au/#/detail/YAH000018

Request for a few jobs as below: • window – 800(W) x 1470mm(H) Need something cover the void area ( existing fly screen not completely fit the window size and left a void area ) • wardrobe hinge fix • 4 rooms new heater racks install • a bedroom door not efficient to close & open (making noise may caused door not balance) • 2x shower screen doors not close properly ( screen not balance) • Blinds change for 3 rooms( Provided new blinds) : • A bathroom room door frame bottom mould damaged (optional ). • 1 x bedroom hydraulic door closer loose • 3 x toilet rail/towel rack loose Thank you.

My dimmable fluorescent lamp has died. It made a loud "pop" and both lamps turned off. I've checked both bulbs with a multimeter (following a youtube video) and confirmed both have non-zero ohms i.e. connectivity so am thinking it's more likely the harness. I can't see any obvious blown components on the circuitboard. This is about where my DIY electrical skills end. I'm hoping someone can diagnose and repair the board if this is possible. I was quoted over $200 for a lamp repair. That's multiple amazon lamps lol. So I'm hoping someone can take this on for a more reasonable price and help avoid more landfill. I can provide more details if required. Able to drop off and pick up depending on the agreed price. The job is for a completed repair.

The Roman blind normally pulls up like in first image. When I went to pull it up today, the folds just all fell down (see second image, behind computer). There was a small cord dangling at top, which must link the loops on the back of the blind to the pulley system. It must have broken on both sides at the same time (the blind is about 7 years old). The last photo shows the metal cord which is used to pull the blind up and down. I think it is just the cord that needs fixing, threading through the loops, etc., but I am not confident to do it myself, would prefer someone with experience of blinds.

I’m looking for a quote to fix - and prevent further - flood damage at my recording studio in North Melbourne due to the recent weather. I’m renting a commercial property, so I’d love someone to come out to see the space in person so we can talk through the damage, and then provide a quote I can pass on to the landlord.

Our wardrobe bracket has come off the wall. It didn’t look like it had very deep screws and was glued in place. My landlord tried to fix the bracket but couldn’t get the drill to work because it is a solid brick wall. We have the new bracket, we just need someone who knows what drill and screws to use to fix the bracket in place.

As per titles. 5 x Wall Mounted Drying Rack - Foldable Indoor and Outdoor Drying Rack (https://vendline.com.au/products/wall-mounted-drying-rack-foldable-indoor-and-outdoor-drying-rack) 2 x Hanger Drying Rack Balcony Bathroom Invisible Clothesline Wire Rope (https://a.aliexpress.com/_mNvc04R)