Find a professional local carpenter in London

I’m looking for an experienced shopfitter / joiner to design and build a bespoke display wall and shelving system for a perfume store. The style I’m after is high-end, luxury retail, similar to the reference images attached. This is not basic shelving – it needs to look professionally finished, clean, and premium. Scope of Work • Custom-built bespoke joinery for a perfume display wall • Recessed wall niches / shelves (arched or rectangular) • Integrated warm LED strip lighting inside shelves and niches • Smooth, high-quality finish (painted or sprayed finish preferred) • Strong, secure shelving suitable for perfume bottles • Overall look should feel luxury, minimal, and boutique Style Reference Think: • Built-in product display wall • Soft ambient lighting • Clean lines and symmetry • Museum-style product presentation • Premium perfume / oud boutique aesthetic (Reference images attached for guidance) Requirements • Proven experience with bespoke joinery or retail fit-outs • Experience installing LED lighting within joinery • Ability to advise on materials, finishes, and lighting if needed • High attention to detail – finish is very important • Portfolio or previous work examples preferred

We need a high quality joiner to put together a Finnmark sauna. We will provide a fully detailed installation instruction manual.

Joiner to fit an IKEA PAX wardrobe for a seamless built-in look. Tasks: assemble, level on 60–100mm plinth, fix to wall, tie units, add MDF side scribes and top infill (continue coving if needed), notch/refit skirting, hang/adjust doors, make good (fill/caulk/sand/prime), remove packaging/waste.

I would like to request a quotation for a small joinery job in my kitchen in NW2, London. I have a tall cabinet where the fridge is built in, and I’m replacing the fridge with a new one that is 20 cm taller. I would like to keep the overall kitchen height exactly the same, but shorten the cabinet above the fridge by 20 cm so that the new fridge fits properly. The job would include: • Removing the top cabinet door and cutting down the cabinet height by 20 cm; • Adjusting the internal shelf and back panel accordingly; • Cutting and refitting the same cabinet door to match the new height; • Refinishing the cut edges to match the existing wood veneer. Please could you send me a quotation (including labour and materials) and let me know your earliest availability for a site visit? Thank you very much, Raquel

We are looking for an indoor standalone display cabinet made from MDF/pine like in the attached two diagrams. This will be propped up against the office window on the inside. On top will rest a model for display. Underneath, the compartments will be displaying 3x 3D printers (hence the large dimensions). This cabinet should be on 6x heavy duty castor wheels so can be moved around (e.g. to allow for easy vacuum-cleaning underneath). Colour of the cabinet should be white. Looking for a carpenter/joiner who can make this quickly and at a good price. This is for a new property business on a tight budget, so please don't quote silly money - but rather with the expectation that, if successful, this will be the first of many orders.

Mitre pre cut skirting to size - room is 4m by 2m. I have a sliding mitre saw. Just need help to mitre cut the individual pieces (7 in total)

We need a joiner to help us put custom fronts on our Ikea kitchen and to create a base for the Besta cabinet so we can use it as a bench.

Joiner to resize and fit 4 internal pine doors. Tasks include resizing, hinging and fitting door lock. Own tools will be required

I need a wooden table assemble however some piece's need it for the assembly process were lost during moving process. I need someone a jouner whocan find a way to put it together the leg's of the table.

Looking for a joiner to install banquette seating in kitchen corner, and remove existing breakfast bar. Also to install shelving in living room alcoves. Small residential project but may be more scope for future projects as I am an interior designer. Please see my profile for further details. Please quote below or contact me. Thank you!

Just had a Wren kitchen fitted and have some spare worktop/cupboard surfaces left over. Looking for someone to make a small kitchen table from one of the remaining pieces.

I have ordered a made-to-measure built-in wardrobe, that has already been constructed in the room it is to go in to (see Picture 4). I need an experienced carpenter / joiner to finish the job by doing the following: 1. Cut out the skirting boards behind the wardrobe, to get a tigher fit to the wall (leaving the skirting board underneath the desk) - Picture 1. 2. Cut out a hole in the back of the left-side unit, to provide access to the plug in the wall. 3. Fix the wardrobe units to the wall 4. Add fitting (provided - picture 3) around the edge of the wardrobe, for a clean, fitted finish. 5. Fit the bridging unit between the two wardrobe units at the top, fixing it to the wall and to the wardrobes - picture 1. Note: the bridging unit is heavy, so this is likely to be a two person job. I am happy to help with the lifting / holding. 6. Add the doors to the bridging unit. 7. Generally ensure a clean and tidy finish. Tools required: circular saw, sander Instructions are provided with the wardrobe, although were of limited use in building the wardrobe, so some improvisation may be needed.

Handyman - Sealant in Kitchen and Bathroom (Material to be brought by the handyman) Joinery - Screw / Fix Mirror in Hallway, Join Book Shelf into Wall Electricals - Bathroom Cabinet Wiring Light, Living Room electric point extension

Sealant around the induction in the kitchen and in the bathroom on the bath board, fixing electric points for the bathroom cabinet. Fixing a book shelf into the cupboard wall Material for the sealant to be brought by the handyman

There are gaps in wooden tiles and below the balcony doors. Need a joiner/ handyman who knows how to fill the gaps. I will pay for the materials.

I’ve already assembled 3 IKEA wardrobes and now need a skilled carpenter or experienced handyman to help secure them all to the wall and create a custom inbuilt/fitted look for one of them. The goal is to make the wardrobes look seamlessly integrated with the room, like a built-in unit. Tasks include: -Securing the wardrobes to the wall safely and professionally -Removing skirting boards where necessary so the wardrobes can sit flush -Adding trim, filler panels, or moldings (if needed) to close any gaps between the wardrobes and the walls/ceiling Ensuring a clean, polished finish that gives the appearance of a custom built-in wardrobe You’ll need: -Experience with IKEA wardrobes (e.g. PAX system) and custom built-in installations. -Your own tools for cutting skirting boards and panels -A good eye for detail and finish -Ability to advise on trim options or any small material additions if required.

Need a really make shift garage door that can be disposed of in a few weeks but needs. To be able to open close and have a padlock on

Joiner or carpenter to shorten the unit. Need shortening ideally one door/ block comes off. let me know if any questions

I have 3 wooden doors that need repairing, they are in a pretty bad state but I would like to be able to patch them up and repair them adding handles (I think I can supply). The reason I’m not changing the doors entirely it’s because the flat is not mine but would like the doors to be functional and safe again. Not sure if the wood can be filled and repaired and new handles placed back in position or different position on door if need be. Please let me know

Bench area needs tiling. BBQ area needs sliding doors.