Find an experienced plumber in Fitzroy VIC

Rheem Electric Hot Water System – Inspection Today (Saturday) – Fitzroy Looking for a qualified hot water technician to inspect an existing Rheem electric storage hot water system today. Water heats intermittently but is often only lukewarm. Need diagnosis of the thermostat, heating element and tempering valve as appropriate. Third-floor apartment, stairs only. Budget: $180 for inspection and diagnosis only. Repairs and parts to be quoted separately. Please confirm your qualifications, availability today and whether your offer includes all call-out and diagnostic costs.

The piece that holds the shower head in place has snapped so we need a new shower head and bar installed. We’ve currently used duct tape to hold the shower head in place as seen in the photos.

Water is cloudy - not sure why

I’m looking for a licensed/experienced plumber to upgrade an existing shower setup. Current setup is a handheld/telephone-style shower with an existing mixer. We would like to replace it with an exposed bottom-inlet retrofit twin shower system in matte black, using the existing plumbing (existing mixer and water supply stubout) and without opening the wall if possible. The shower hardware will be purchased separately and supplied on site, so this task is for installation only, with any other consumables and tools to be provided by you. Selected product: Fienza Kaya Retrofit Twin Shower, Matte Black https://www.thebluespace.com.au/products/fienza-kaya-retrofit-twin-shower-matte-black Note: The Fienza Kaya Retrofit Twin Shower includes the water inlet hose and the flexi hose for the handheld shower component. Scope: 1. Review the attached photos and confirm whether this retrofit shower system is compatible with the existing setup. 2. Confirm whether the existing outlet is a standard 1/2" BSP fitting and whether any adapter or extra part is needed. 3. Remove the current shower fitting as required. 4. Install the retrofit twin shower rail/system using the existing plumbing where possible. 5. Avoid opening the wall unless absolutely necessary. 6. Test for leaks and make sure everything is working properly. Please only quote if you have plumbing experience. If wall access is needed, please let us know before proceeding. I have attached a comparison image showing the existing setup on the left and the proposed retrofit twin shower system on the right.

Hot-water mini-stop/isolation valve in our apartment laundry is leaking. The valve continues to pass a slow drip from the outlet even when turned fully off. The cold-water valve appears to be fine. Looking for a registered/licensed plumber to inspect and repair the hot-water mini-stop valve, or replace it if required. The valve is exposed and easily accessible in the laundry cupboard. Please let me know whether your offer includes call-out, labour and any replacement valve/materials, or if parts would be additional.

I have just installed a new sink and need a plumber to connect the sink to the waste

I'm looking for a licensed plumber to inspect and repair two issues in my bathroom: Toilet: The flush isn't strong enough and often requires multiple flushes to clear the bowl. Bathroom sink: The basin drains slowly because the plug/waste keeps getting clogged. I've cleaned it before, but the problem keeps returning. I'd like the blockage cleared and the underlying cause fixed if possible. Please bring any standard tools and parts you think may be required. Let me know your availability and whether your quote includes inspection, labour and any minor parts.

Hi, I need someone to fix the handle on the front door, reattach the towel rail, repair or replace the toilet seat, and fix a crack in the bathroom cabinet. Thank you!

Connect dishwasher Connect washing machine Check leaking pipe under sink Check tap connection

Our gas hot water system has had poor hot water for the last few days. We’ve now noticed active water leaking underneath the unit with visible steam/vapour coming from behind the system. We’ve stopped using hot water and need someone to inspect it urgently.

We recently bought a house. Hydronic system seems to be working and was fine the other day but I’ve changed a setting on it when I was trying to figure out how to turn it off, now I can’t seem to get it to work again. No error codes, pretty sure it’s ‘operator error’. The hot water system is not lighting and needs a new thermocouple. Genuine service job please, we don’t want anyone who tries to sell a new unit. Looking for a plumber or gas fitter who can help me get these workings. Also check my washing machine connections too. Flexible with times and days, shouldn’t take much because I’m sure the hydronic are a simple fix, mainly just the thermocouple.

I need water pipes and drain pipe fitted to a shower and basin. Roughly 1.5 metres away from where that old/ original water and drain is now. EST 3 hours work.

Looking for a licensed plumber / gas fitter for renovation rough-in work in Melbourne. Current condition: • Floor is already opened up, so access under floor is available • Old gas heater needs to be removed • Existing water pipes to be upgraded / rerouted to PEX • This is a renovation rough-in stage, not final fit-off yet Scope of works: 1. Safely disconnect and remove existing gas heater 2. Properly cap / decommission gas line in a compliant manner 3. Inspect existing water lines and replace / reroute suitable sections with PEX 4. Rough-in hot and cold water lines for current / revised layout 5. Install / replace isolation valves where appropriate 6. Minimise inaccessible buried joints where possible 7. Pressure test rough-in before close-up 8. Advise if any existing drainage / water points should also be updated while floor is open Requirements: • Must be licensed in Victoria • Must have experience in renovation rough-in work • Must be able to provide compliance certificate if required • Please mention what is included / excluded in your quote • Please confirm whether quote includes materials or labour only Please quote with: • Labour only price • Estimated material cost • Availability • Licence details

Part of my shower head fell off the tiles and needs to be glued back on. Don’t think it requires any screwing but happy to be told otherwise.

Fix two leaking taps and a shower head One tap i have already replaced the valves, and that hasn't worked well. I'd like the tap to be ground down and flattened as i think that's the issue. The

Fix toilet seat hinges , to make them secure as they slip around

Unit is under a cupboard and needs to be taken out to access it. Have no idea how to take the cupboard out.

Looking for a plumber to complete the final fit-off for a bathroom/sauna area. Rough-in complete. Need someone reliable to finish and check existing work.
 Scope includes: * Install shower set (existing outlet in place) * Install and connect basin + vanity unit * Fit off mixer/tapware * Connect waste and water lines * Check seals and waterproofing penetrations * Pressure test and ensure everything is working correctly
 Fixtures (links available): * Combination Shower - https://yabby.com.au/products/combination-shower-straight-shower-sprayer-antique-brass * Shower Wall Mixer - https://tilecloud.com.au/products/sydney-wall-mixer-antique-brass-1 * Shower Drain - https://www.draintek.com.au/wedge-wire-shower-grate-120mm-stainless-steel-standard-lengths-satin-black.html * Vanity basin - https://www.perini.com.au/basins/harmony-basins/T45136/ * Vanity base - https://www.austpekbathrooms.com.au/products/otti-byron-black-oak-900mm-floor-standing-vanity * Basin drain - https://www.buildmat.com.au/products/32mm-brushed-vintage-antique-brass-pop-up-waste?variant=45319668826332 * Basin tall mixer (faucet) - https://www.buildmat.com.au/products/mira-brushed-vintage-brass-tall-basin-mixer?variant=44376335614172 * Supply any additional connectors or fittings if required
 Notes: * Existing work is partially completed, so need someone confident picking up and finishing * Plans and photos attached. Layout and fixture positions are defined * All fixtures are on-site and ready for installation
 Please confirm availability and experience with similar fit-off jobs.

We’re opening a new café soon and looking for a plumber to assist with a straightforward fit-out job. Scope of works: • Disconnect existing water supply • Move the current sink position over to the next cabinet door • Install an additional sink (currently 1 sink, we require 2) • Relocate taps and hot water system into a newly built cabinet • Reconnect all plumbing after the new benchtop is installed • Connect coffee machine and jug rinser to water supply • Ensure all work is compliant and certified Overall, it’s a simple disconnect, adjust, and reconnect job as part of our benchtop upgrade. We may also need help cutting the benchtop to fit the sinks and equipment. If you have the right tools and experience, that would be a bonus. Let me know if you have any questions.

My gas storage hot water system (AquaMax 390SS-NG) has stopped producing hot water. The pilot light will not ignite. What’s happening: • The pilot is out and won’t relight • The red igniter button clicks, but there is no visible spark • Not sure if pilot gas is flowing • The big control dial turns, but pilot position isn’t responding normally • No flame appears at all