Find experienced local tradies in Inner South Melbourne

Hi everyone! Just wondering if there are any local tradies or handymen available tomorrow (Thursday) to help hang some blinds in our 2 bedroom house? I would say 2 hour job 📍 Located in Bonbeach Please inbox me if you’re available! Thanks so much 😊

I have a window in our kitchen, approximately 2000 x 700. I need the internal reveals plastered and external beads put on the verticals and top. I have the gyprock and trim.

We have done some demolition and now require walls to be re-plastered, materials supplied. Already purchased panels, and gyprock

Install outdoor rated dual power point, must be rated to support 1800W. Existing power point is available, installation height around 2.5-3m.

Two small renders jobs see photos

Small area of render required to be patched where previous camera mount was attached. Will need to have that area patched. Not sure on the exact colour - maybe Lexicon Half. Area will be eventually covered again with another camera mount.

There are 3 steel shelf brackets (used for a heavy timber shelf) that need to be removed. There are further holes in the wall as can be seen in the photo that will need to be filled in (with expanding foam or similar) and then plastered to create a neat flush wall. The screws also need to be removed and patched up.

One PowerPoint is buzzing and needs replacing, we have a replacement. A second outdoor PowerPoint needs replacing as when one side is off it appears to still be able to be used.

I’m looking for an experienced renderer to repair and re-render part of an exterior wall on an upstairs balcony in Carrum. Recent roof and gutter repairs around this wall have left some of the foam backing exposed near the top. The wall is approximately 3.2m high. The left section is about 97cm wide and has foam backing behind the render, while the adjoining section to the right has brick backing. There was previously a crack in the foam-backed section as the house settled, around the point where the different substrates meet. This was temporarily patched and painted, but I would now like the area properly repaired and re-rendered. My preference is to: 1) Re-render just the foam-backed section on the left, from top to bottom, rather than the entire wall if practical 2) Properly repair the exposed foam and previous cracked area 3) Include an expansion/control joint where the foam-backed and brick-backed sections meet if this is the appropriate way to prevent future cracking 4) Match the existing rendered texture and Colorbond Monument colour as closely as possible The entire two-storey wall is likely to be repainted shortly afterwards, so an absolutely perfect colour match isn’t essential. Access is from the upstairs balcony. Photos show the wall, exposed foam, previous repair and approximate dimensions. Please include all materials and let me know your proposed repair/rendering method when quoting. I can provide more photos if needed.

Need 4 Power points run in a new workshop. Mezzanine level is exposed, so minimal drilling etc. 3 x 4 outlet GPO and 1 x 2 outlet. About 10 metres of conduit. 2 separate circuits with RGB etc. Plenty space in the fuse box. Happy with an apprentice etc.

Looking for someone experienced with glass balustrades/glazing to replace the deteriorated black glazing rubber/wedge gaskets along the bottom of 5 glass panels on my balcony in Carrum. The existing rubber has shrunk, curled up and is coming out of the aluminium channels. The job is to remove the old rubber, properly clean out the channels, then supply and install the correct replacement black glazing gasket/wedge across all 5 panels. The work is on the outside face of the balcony balustrade, as shown in the photos, so please allow for appropriate external access to complete the job safely. The glass and aluminium are otherwise fine. I’m just looking for the rubber/gaskets replaced and the channels cleaned properly. Photos attached.

- Two power points moved approx 400mm to the right on the same wall - Antenna socket to be disconnected A wardrobe is being fitted to this area so no plastering of the old holes will be required.

Need a licensed electrician to inspect and replace a cracked kitchen power point. It previously buzzed once and had a burning smell, but is currently no buzzing, smell or heat. Please inspect the wiring for any damage/overheating and replace the power point.

Need this installed- someone handy with a drill and follow install instructions. See all pictures of parts included and how it looks. A local tradie in Cheltenham

Needing an experienced plasterer to quote for approx 11sqm of plastering - ceiling, walls, etc before cabinetry gets instaled. Job is in McKinnon.

Looking for an experienced painter to paint our rendered brick fence in the front yard. The fence is already rendered and just needs to be properly prepared and painted for a clean, professional finish. Job includes: Preparation of the rendered surface as required Painting the full rendered brick fence Keeping the surrounding area clean and tidy Professional, neat finish Paint will be provided. Please refer to the attached photos for the size and condition of the fence. We would ideally like this completed this week, so please only respond if you have availability. Please include your availability, experience with exterior rendered surfaces, and whether your quote includes paint/materials. Located in Caulfield South. Frontage is roughly 15m, includes driveway opening

I need a plasterer to fix a small hole and have it repainted and fixed as the original

Need a large telescopic dog door installed into an external wall (plasterboard internal side, weatherboard external side). Looking for someone experienced with cutting into and framing a wall opening, and finishing/sealing both sides neatly ensuring a weather-sealed finish. Details: Dog door supplied by me (large/telescopic size) Wall type: plasterboard (inside) / weatherboard (outside) Own tools required When: Saturday 15th or Sunday 16th August Location: Bentleigh, VIC