Find a professional hot water system contractor in Inner South Melbourne

Hi, I’m looking for a licensed plumber to assess and fix a hot water pressure issue in my older (1940s) house in Brighton East. Problem: * Cold water pressure is strong * Hot water pressure is weak * Hard to mix temperature (either too hot or too cold) * Possible roof-mounted / gravity-fed hot water system? Maybe needs a tempering valve?

Issue: Solar tank and gas booster both seem to be operating okay. Suspect faulty tempering valve with orange cap causing intermittent lukewarm/cold water. Gas Booster is T26 eternity and solar tank is chromagen 300 Litre tank. Both were installed about 10 years ago and first time having this issue.

Hot water not coming. Plumbing

Shower hot water tap knob falls off spindle

Hi, I need a quote to split the hot water line under my laundry sink so I can connect a new washing machine. Currently, there is only one hot water outlet. Task: Replace existing single with a dual-outlet. Install LG washing machine Timing: Looking to get this sorted today (Saturday) if possible. Please give me a ring to discuss.

My hot water service pilot light has been blown out. I need someone to come and relight it for me. The unit is a freestanding unit, attached to the wall in my back garden, accessible via a concrete path.

Rennai old hot water unit Split in copper pipe and it’s spraying water out Need it fixed by a licenced plumber

There is a leak on the inlet side at a compression joiner. Probably needs to be replaced

I’m looking for a plumber to connect an outdoor hot water shower. The shower is approximately 18-20m from the closest hot water outlet (access will involve connecting under a raised kitchen wooden floor). The shower is a combination style, with a separate mixer. The connecting pipe will need to navigate out to the new shower outlet along a fence line. Please include installation of all connecting pipes (using PEX for the large span). Please also include installation of the outlets and mixer unit into the outdoor wall. (I will be able to install the shower to the wall face once the wall is clad). As this job has a few permeations, happy to talk through final price after a site visit. Photo shows

I have an Aquamax G390SS hot water tank that has recently started to leak a steady stream of water from the pressure relief valve. • When I turn off the cold inlet to the tank, the leak slows right down. • When I turn it back on, the flow increases again. • Cold water pressure in the house feels strong. • The council recently changed our water meter. I’d like you to: 1. Check the mains water pressure at the property 2. Confirm whether I have a pressure limiting valve and whether it’s working correctly 3. Check whether I have an expansion control valve and if it’s functioning 4. Replace the PTR valve if required The system is about 5 years old.

Pilot light in Aquamax appears to be going out needs to be checked by licensed plumber. Model number is : G390SS-NG

The gas supply to hot water has stopped, the house has gas but the hot water system does not let the gas flow.

Looking for a licenced plumber to install a wall mounted hot water service. Need to disconnect the existing one and place in a similar spot.

Hot water system pulsating/clicking. Need urgent service. No after hours fee - straight up.

Hot water not working. It’s luke warm. Runs on gas and has a rinnai system

I have no hot water. My hot water service may need the pilot light turned on.

Looking for a plumber to look at hot water system as the water is not heating up .

Hot water heater leaking water

Hi there, Our hot water system needs replacing. The job is just for install. Size is 25L. Located in Brighton off church Street.

Hey there! We run a mobile pet grooming business, and our Camec hot water system (similar to what’s used in caravans) has started showing an E9 error, which we’ve read means it’s having trouble igniting. It could be: • A water pump issue (low pressure or flow) • Or something directly with the hot water system ignition or gas supply We’re looking for someone experienced with Camec or caravan-style hot water systems who can come out, diagnose the issue, and help get it running again. Job details: • Located in Edithvale • Hot water system is installed inside a mobile grooming truck • Access and setup similar to a caravan installation What we need: • Diagnose the cause of the E9 error • Repair or advise on replacement parts if needed • Test and confirm the system ignites properly again Budget: Approx. $150–$250, depending on what’s required (happy to adjust if parts or extra time needed).