Find a professional local carpenter in London

Looking for a carpenter or joiner to supply and fit a custom MDF panel to fill the gap between kitchen wall units and the ceiling. The kitchen includes corner cabinets and a slightly uneven ceiling, so precise cutting and fitting will be important. The goal is a clean, contemporary finish — ideally spray-painted white in matt, with light caulking where needed to smooth the edges. Experience in kitchen cabinet finishing or similar bespoke joinery work preferred.

I wanted to see if a joiner could make some bespoke wardrobes in my master bedroom. Ive shown the rough size ideas in sketchup with some images of design intent and colour palettes etc. Ive also shown some ideas from Ikea Pax and would like some ideas how these could be adapted into a fitted wardrobes and then fitted in and painted etc. Suggestions welcome as well

In short, had an extension done recently but the builders left a job unfinished. There’s a slight raise going from the original part of the house to new bathroom. Looking for someone to make it look a bit more seamless.

Built in wardrobe from floor to ceiling , I want to move the wardrobe to another part of the room.

I have joint in cabinetry, but would like to install grommets for wires: https://www.amazon.co.uk/Grommet-Grommets-Tidies-Desktop-Organizer/dp/B0DRFMY3WX/ref=asc_df_B0DRFMY3WX?mcid=f680b28c6e0439289c5e877e64941239&tag=googshopuk-21&linkCode=df0&hvadid=725810329396&hvpos=&hvnetw=g&hvrand=6948099056472555000&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9045998&hvtargid=pla-2393514816627&psc=1&gad_source=1

I need a carpenter/joiner to remove the existing lock and install the new one - please see images and two handles. I will provide the hardware. Will need some timber to fill the existing hole and notch the door.

Howdens kitchen being fitted so looking for joinery supply for a single vent cabinet. Fitters lined up so Supply only. IMPORTANT - must match elmbridge porcelain shaker cabinets in colour and look. 3 panels needed - 1m by 50cm 2 x 50cm by 30cm

Carpenter needed to make the ikea wardrobe like fitted inbuilts with base and plyboard on the sides. Also to trim the width of the 50cm wardrobe to fit in the remaining gap. The wall is about 340cm. you can visit the house to check.

A joiner to add wood trims to sides of wardrobe

Joinery as part of renovation project: - 2 sets of bedroom cupboards (shaker style) - Utility - Simple open shelving to house washing machine/dryer - Understairs nook - seating, pegs

Two alcoves that require shelving Skirting on one wall 4 drawers for cupboards

In the Kitchen: Remove existing tiles, level up d floor with plywood and attach new vinyl to floor. Reduce the size of the Island table by a 3rd. Replace the worktop with a new one, create space 4 electric hob. Replace the cabinet handles. Replace 4 cabinet doors. Relocate the washing machine to next unit. ( 2 feet from current location) Replace the plinth with a new one. Remove a set of base and wall units by the entrance door.

Cupboards built to cover boiler and water tank etc in our utility room. Would also like 1 cupboard to be sturdy enough for both a washing machine and tumble dryer.

would like some shelves made to fit in small broom cupboard but also some drawers to be made on runners inside wardrobes

I need sloping wall shelves made for bakery

Renovation assistance; No tools required 9am-5pm 1 general handyman required to assist with the following - Paint strip and sand joinery (cupboard doors, skirting, Cills) - Filling & making good walls in readiness to paint - Preparing floor for new carpet including removing staples & screws

I need to replace my internal doors with fire rated doors. I need a carpenter/joiner who can install the fire doors with the accompanying accessories including architrades, door frames, door locks with handles and keys, door closers, stops and other accessories needed to make the 9 doors fully fire rated compliant. I am looking for somebody who is well experienced in installing fire doors.

Looking for a builder/carpenter/joiner to fit a full length tambour door on the balcony, attached photos of what the door would look like. There is a second task of fitting a toilet roll holder.

We repurposed a shelf to decorative cupboard. We are left to cover the back and sides. For the back, we are using leftover floor boards and for the sides, hardboard. What's needed from you: 1. The floor boards cut to size and installed at the back 2. The hardboard on the sides we need to cut and install. 3. The hardboard needs to be decorated with cane panel and mouldings on the border 4. Wall Mount the re purposed shelf. We will provide the materials but need you to bring tools to cut and install- saw, drill, glue etc. We can provide with necessary nails and screws.

Hi. I would like some cupboard doors made to cover some shelves in a sitting room, similar to the ones shown in the photo. They are flush with the wall and set in the opening and very high at about 2.5m and a similar width. MDF is fine and with push catches. I am then interested in putting beading around the joins to hide them and make it look like panelling. If I can find the right person, I have other bigger projects that need doing. Have included a nominal price, not including materials, a quote might be best. Thanks for reading.