Find a professional local carpenter in London

We need to make the cooker hood canopy (115cm wide) and arched wall cabinet (just the top part) 130cm wide in kitchen alcove. Both marked with green highlighter in photos

Carpenter / joiner required to make 94 custom timber roof dentils Looking for a carpenter to manufacture 94 decorative roof dentils. The dentils have a curved profile (see attached photos) and come in four different dimensions: 69* 300x140x100mm 7* 280x140x100mm 4* 400x140x100mm 14* 510x140x100mm These must be made from solid hardwood, primed and finished in a quality, weatherproof outdoor white paint. Delivered to site in Barnes SW13 London. Looking for best price and turnaround. Budget: £1200. Other parts will be required as well throughout the project and other sites.

Carpenter required to make 94 custom timber roof dentils Looking for a carpenter to manufacture 94 decorative roof dentils. The dentils have a curved profile (see attached photos) and come in four different dimensions: 69* 300x140x100mm 7* 280x140x100mm 4* 400x140x100mm 14* 510x140x100mm These must be made from solid timber and finished in a quality, weatherproof outdoor white paint. Delivered to site in Barnes SW13 London. Looking for best price and turnaround. Other parts will be required as well throughout the project.

Need to lay out a wallpaper in a small bathroom. Two sections: a slanted wall and a slanted piece of joinery with doors etc. 200cm in width total. See pictures.

Analysis of carpentry and joinery jobs around home

I recently had some shelves, cabinets and a faux fireplace made from MDF. I just need a few small tweaks to the job like reattaching a plug socket to the wall (hole is too big behind the plug) , and creating a back panel for the fireplace

I there. I have two internal doors that need fitting. We have the hinges, doors, and locks. The doors are new and don't have the grooves for hinges/ lock cut out.

I would like to hire a carpenter/joiner to build the wooden base for this seating. There will be a radiator housed under it so it needs gaps/slits to let the heat through. I want the base to look like in the photo. Rough dimensions are in the photo. Price would need to include materials.

Experienced and excellent Joiner, Carpenter required for High End finish of 4 wardrobes, 1 book shelf, 1 shoe rack. # Min 20 years experience # Refs and portfolios required Strictly no time wasters Top money for the right person

The cupboards are already assembled.3 kitchen lower cupboards to be mounted and a waterfall counter. A sink hole to be cut along with hob to cut. 45 angle counter cut rather than end strips

Veneer application to spiral staircase wall (curved MDF substrate already fitted). Area approx 10–12 m². MDF is smooth(ish) but needs further smoothing/filling and edge prep. Require seamless professional finish with joins kept minimal/hidden. Veneer to be stained after application. Veneer provided by me. This is a job for someone that enjoys intricate work.

Replacing 4 internal doors and frames. make adjustments to build in wardrobe

Building L shape kitchen breakfast bar. Build banquette seating. Replace radiator to smaller radiator Labour only.

Below are the deficiency noted by the local authority for my HMO compliance: - Smoke seal partly painted over, which reduces its flexibility, impeding its ability to block smoke. - Ill-fitting bedroom door with gaps of more than 4mm or less than 2mm between the fire door and the frame. This can compromise the fire door integrity by allowing smoke and fire to pass through more easily (The 2–4 mm gap applies to the two vertical sides and the top edge — this ensures the intumescent strips and smoke seals will perform properly in a fire. Too large a gap (>4 mm) may allow smoke and fire to pass through. Too small a gap (<2 mm) can cause the door to stick or not close properly. - Thumb turn lock not available. - Door doesn’t self-close. Severity Severe Below are the sugested remedy - Appoint a reputable fire door remedial service provider to assess and carry out the necessary repairs. The smoke seal must be fully replaced – The smoke seal must be certified UKCA/CE. - Adjust the door so that the gap is between 2mm and 4mm. Test and leave in proper working order. - Install a lock to the bedroom that can be opened from the inside without the use of a key, i.e. a thumb turn lock - Overhead self-closer: Inspect and adjust the tension and closing speed. Ensure that the door always self-closes. I am therefore looking for a professional who knows how to accomplish the above for 8 doors.

Staircase restoration, sanding, stripping, skirting

Hi, I’m looking for an experienced joiner/carpenter to help with 3 internal doors in my flat in SE1. Details: • 1 × bedroom door • 2 × storage cupboard doors • The existing doors have been removed • The openings are non-standard sizes What I need initially: • A site visit to accurately measure all openings (top/middle/bottom) • Advice on door sizes & clearances • A quote for supply + fitting of plain internal doors • No obligation to proceed after measuring Important: • Looking for someone with experience fitting internal doors (not general handyman only) • Please confirm if you charge a call-out fee • Photos/examples of similar door work appreciated This task is for measurement + quote first, with fitting to follow if we agree on price. Thanks!

2.4m long acoustic panels (qty 3.5 panels, pic 1) and Left over kitchen materials (pic 2)

Skirting board was put in too high for the radiator to fit. We need the skirting board altered so that it can fit underneath the radiator

I’m looking for an experienced shopfitter / joiner to design and build a bespoke display wall and shelving system for a perfume store. The style I’m after is high-end, luxury retail, similar to the reference images attached. This is not basic shelving – it needs to look professionally finished, clean, and premium. Scope of Work • Custom-built bespoke joinery for a perfume display wall • Recessed wall niches / shelves (arched or rectangular) • Integrated warm LED strip lighting inside shelves and niches • Smooth, high-quality finish (painted or sprayed finish preferred) • Strong, secure shelving suitable for perfume bottles • Overall look should feel luxury, minimal, and boutique Style Reference Think: • Built-in product display wall • Soft ambient lighting • Clean lines and symmetry • Museum-style product presentation • Premium perfume / oud boutique aesthetic (Reference images attached for guidance) Requirements • Proven experience with bespoke joinery or retail fit-outs • Experience installing LED lighting within joinery • Ability to advise on materials, finishes, and lighting if needed • High attention to detail – finish is very important • Portfolio or previous work examples preferred

Joiner to fit an IKEA PAX wardrobe for a seamless built-in look. Tasks: assemble, level on 60–100mm plinth, fix to wall, tie units, add MDF side scribes and top infill (continue coving if needed), notch/refit skirting, hang/adjust doors, make good (fill/caulk/sand/prime), remove packaging/waste.