Find an experienced handyman in Malvern East

I have an Aqara Roller Shade Driver E1 installed on the wall that controls 3 roller blinds. It used to work fine, but recently the roller chain keeps getting stuck inside the motor when it runs. The other end of the chain seems loose or misaligned amd gets tangled. Need someone to inspect, adjust, or refit the chain so it operates smoothly again

Retractable fly screen for sliding door. 258cm wide X 234cm high approx. supply and install

Relocate large clock to another wall. Hang two mirrors Wire and mount two #44 inch TV’s (electrical work required for one tv) I have screws and one bracket. May have to get another bracket from Bunnings or JB.

Hole is around 19cm wide and tall on a plasterboard wall. Kids were playing and made the hole.

We are replacing our internal doors. It is a single story house. So we will purchase the doors and handles - we then want someone to install the doors x 7. The door sizes are 6 standard (2040x 820) and 1 is 2040x920. The handles are standard.

Need someone to install steel gate into brick pillar.

Hi! I’m looking for someone experienced with peel-and-stick wallpaper to install some on one wall in my apartment. The area is approx. 160 cm tall × 300 cm wide. The wall is smooth regular plaster, but does have a slight slant. The wallpaper is already supplied. It is a mural so will need to be lined up (and I don’t trust myself to be able to do this so hopefully you can).

Just need adjustment and possible replacement (of hinges or just screws) so cupboards open and close smoothly. Definitely a couple of screws missing. Fairly quick job hopefully.

My shower screen has come off the frame, with the frame splitting per photos attached. Looking to have this fixed.

After a handyman to help with two tasks! 1. We’ve bought a Yale SL smart loco for the front door but unfortunately have an oval bore instead of the circular one this is fitted for. Hoping to get someone who can saw the bore to an appropriate size to install it! 2. Our front gate has been wonky on its hinges since we got the property - over time the top hinge has loosened and now the door need to be lifted and slammed just to get it open/closed. The posts are metal so we’re unable to redrill the hinge in ourself. Hoping for some help with this! Quite flexible with the timing, so please let us know if you can give us a hand with either task!

Replace broken glass, supply materials.

There is a loose rubber seal part floating around that should be fixed to the one way valve where water passes from the pump towards the pipe up the side of the house. This piece needs to be reattached so to ensure water can pass freely up to the roof.

Hi, A sign post was attached to the fence pales with rope ties and unfortunately due to the wind, the pales have been ripped off as the wood was rotten. Looking to replace thr horizontal beams behind the pales and have the pales reattached. Thanks

I need a handyman to come and do some minor repairs as part of our end of lease (see images attached) -fill small hole in wall -re attach towel rack -fix door hinge -fix tile -remove markings on wall -repair light fitting Byo tools and materials.

Needing a handyman in East Malvern tomorrow for some maintenance- Wardrobe door reattached (hinges on site) Cut back a timber veneer benchtop for 2 laundries. Benchtops and brackets in site Door handles x 4 attached to vanity

Handy man needed today in East Malvern to attach a freestanding vanity to wall. Will also need to cut a hole in the back of the unit for plumbing.

Hi, A little bit of the timber door frame has gone bad as pictured. Looking to replace that little section with fresh wood. Materials not supplied. Thanks

Urgent decking board removal for access point creating for plumbing and digging hole. And create a trap door/access in deck.

Description: One of the side protective bars (runs along the lower edge of the car body) on my 2016 Honda HR-V has come slightly loose — one of the fixings is broken, causing it to sit slightly ajar. I need someone to securely reattach it so it looks flush with the body again. I’m not particular about how it’s done — zip ties, screws, washers, adhesive, etc. — as long as it’s safe, looks clean, and holds up over time. Photos attached for reference. Ideal for: • Mobile mechanics • DIY car fixers • Anyone handy with car bodywork

I have a Heat n Glo Mezzo 1300 AUB fireplace. It has a RC300 remote. The remote has always worked but this morning it has somehow un-paired itself from the fireplace. The remote is still fully functional, just not communicating with the fireplace anymore. Need help finding the control module for the fireplace, and putting it in pair mode again so that the remote will work again. Fireplace is a 2-sided see through fireplace that's built into a floating wall. I've removed the front panels but haven't been able to obviously see the control module.