Find trusted local electricians in Newtown NSW

We currently has 40 downlight fixtures installed in the ceiling. The ceiling already has existing cut-out holes from the previous lighting setup. We are requesting an electrician to replace the existing lights with new LED downlights of the same size and type. No new holes are required — only removal of the old fittings and installation of new ones. Scope of Work: • Remove and safely dispose of 40 existing downlights • Install 40 new LED downlights into existing ceiling cutouts • Connect all fittings to existing electrical circuits • Test and ensure all lighting functions properly and complies with safety standards

Hi there! Looking for AC installation. Brand Kogan Link to product: https://www.kogan.com/au/buy/hyundai-52kw-inverter-smart-split-system-air-conditioner-reverse-cycle/ 5.2 KW Back to Back is possible Bedroom on the second floor of the 2-storey building Unfortunately no plans of the house available but few photos attached Any questions, please ask.

We have two light fittings in the roof of our living room hoping to be replaced with new fittings.

Replacing 2 hard wired clipsal fire alarms. I have removed the old ones and will purchase the new ones Model # 755PSMA4. The plug to the clipsal from my mains is now different and needs to be changed. I also have pully light that was broken by kids and I have new part to install. I am very happy to fit around other jobs in the area

install skylight on single story corrugated tin roof Ceiling is made from wood I can provide the custom made flashing for the skylight already purchased. Measurements are in the photos of the skylight

The property is set up for an FTTN (Fibre to the Node) connection, which should run through the phone lines. However, I haven’t been able to locate any telephone wall sockets on site. I need somebody to come out to the property to investigate and, if needed, reinstall a socket so the internet connection can be restored?

1) Install 4 × Iris wall lights (fixtures + globes supplied). Mount, connect to existing lighting circuit/switching, test. 2) Replace 7 down lights. Remove DL1362/WH 13 W Samsung 5630 LED (hard wired) units and fit pluggable Arlec ALD295 tri-colour LED down lights. 3) Replace 2 single GPOs with double power points. One location has damaged plaster (see images). The down lights + light fixture & globes and wall outlets are supplied.

Electrian Needed for Newtown NSW We have a lightbox and boxhead sign. These light up. Currently the power is being used to power the automatic doors. Just need both the lightbox and boxhead sign (attached) to be connected to power - and put onto a timer. We also have automatic doors (can we check if we can adjust how far they open up) - if that is possible too. The same is quite wide and open when the doors are fully open, and would like the full open width to be slightly reduced. Summary -signs plugged into power - signs on a timer - automatic doors open adjusted Location is Newtown NSW

Suspect our external power point has suffered some water damage and need to replace it

I have a lamp that needs rewiring. Will need to provide the part that holds the bulb because this is the part that is broken. Must suit B22 bulb.

I need a licensed electrician to complete the following work: 1. Downlight replacement • Remove existing downlights (DL1362/WH 13 W Samsung 5630 LEDs with separate drivers, dimmable, 6000 K). • Existing drivers: Constant Current Dimmable LED Driver, 200–240 V input, 25–39 V output @ 340 mA. • Install new Arlec ALD295 9 W Tri-Colour Dimmable LED Downlights . • New lights are plug-in type, IC-4 rated, tri-colour switchable (3000 K / 4000 K / 6500 K). • Check dimmer compatibility and confirm all lights function correctly. • Dispose of old fittings. 2. Power outlets • Replace 2 existing single power outlets with new outlets that have 2 power points each. • One outlet location has broken plaster behind it, which may require securing or a mounting solution for the new GPO. Requirements • NSW licensed electrician only. • Must provide Certificate of Compliance for Electrical Work (CCEW) upon completion. • Bring required tools and test equipment. Quantity • Downlights: 7 • Power outlets: 2 outlets replaced with double power point outlets.

Two ceiling lights in the bathroom to be installed by a licensed electrician. There are currently two small LED lights but these need to be replaced with large Kabomba (ikea) bathroom lights. It should be quite a quick job. See pics

I need two power points installed. I have the power points and they are in place just need to be wired in.

Located Marrickville. One dimming switch Available for connection

Need to install the LED light in the coldroom

its been in action but it keeps beeping even though the battery has been changed. Also, a lamp blew at a powerpoint and I want that checked too.

Hubitat electrician needed with experience in smart home technology and automation to reset all clipsal dimmers in home (est 12 of them) and connect each to the app. I have the Hubitat hub . (bought to replace non working Nero box) Also want to Slow down the manual dimmer switches. Must be familiar with smart home and dimmers

I have a light fitting I want to permanently fix to a metal cap - currently dangling by a wire. I’ve tried super glue and heavy duty tape to no avail. Job completion = permanently fixed with NO visible screws etc

After a spark the hot bar turned off. Not turning back on.

Hot at in restaurant not working, short circuiting.