Find trusted local electricians in Enmore

Please provide a quote for the initial inspection, testing, and certificate lodgement fee. Let me know your availability. I am looking for a licensed electrical contractor with experience in RV, caravan, or motorhome certifications to inspect, test, and certify an existing 240V electrical installation inside a completed Mitsubishi Rosa bus conversion. The vehicle is being registered as a Light Rigid (LR) private motorhome in NSW. I require a formal Certificate of Compliance for Electrical Work (CCEW) digitally lodged via the Building Commission NSW eCert portal to satisfy my VSCCS heavy vehicle engineer. Project Details & Status: • Vehicle: Mitsubishi Rosa Bus (24-seater stripped down to a 2-seat motorhome). • Wiring Status: The 240V wiring has been conducted by myself (owner-builder) and is fully completed. • Transparency: I know all the wire routes, access points, and component locations inside out and will be on-site to assist you, remove panels if required, and show you exactly how everything is laid out. Key Setup Features Include: • Internal double-pole power outlets. • Dedicated consumer unit/sub-board with RCBO/Safety Switch protection. • Inverter system. Scope of Work Required: 1. Conduct a thorough visual inspection of the accessible wiring and component placement to ensure general safety. 2. Perform mandatory electrical testing (continuity, insulation resistance, polarity, and RCD trip times) to comply with AS/NZS 3001.2:2022 standards. 3. Advise on any minor defects if found so they can be rectified. 4. Digitally sign off and lodge the CCEW on the NSW eCert portal. Requirements: • Must hold a valid, current NSW Electrical Contractor Licence. • Must be familiar with RV/Caravan wiring standards (AS/NZS 3001.2). • Must be willing to inspect and sign off on owner-conducted work if it meets code.

Slightly wet main switch board

I have had two skylights installed on the roof already but need the internal work done to finish the installation. Details are below. Please be clear if your quote does or doesn't include materials and give a materials estimation cost if it doesn't (I understand paying separately for materials is favoured by some AirTaskers): Skylight 1 - skylight tunnel, photo 1 - Velux VSS C04 Solar 550 x 980 on a pitched roof - Require build and painting of approx 300mm shaft depth skylight tunnel to the skylight - Standard rectangle opening, including timber frame and plaster - Ceiling is plasterboard and 2.4m height at low point of pitch as shown in photo. Skylight 2 - ceiling installation, photo 2 - Velux sun tunnel TWF0K14 with flexible shaft - Require installation in flat ceiling, easy access to tunnel via attic - Ceiling is plasterboard and standard 2.4m height

Fitting outdoor power plug onto spa bath motor

Looking to install a power point on the wall in the picture, in the middle of the two mirrors, please only licensed electricians. Can either do Monday 25th of May or Saturday 30th of May.

Need to repair a Daikin floor mounted unit leaking water when it’s ON Model number FVXS35RV1

Two jobs for electrician 1. Wire up cooktop- will need to supply junction box to go in cabinet. 2. Wire up pendant light in hallway. New light is supplied. To be completed before Wednesday.

Add 6 power points. Run some cat 6 cables.

The power in the attic room was confirmed connected on 11th November, but the tenant has reported that there is still no power in the unit, even though all switches are on.

Install 3x ceiling light fans

We have an older property in Enmore and would like the electrics inspecting and testing for any defects, this would include the fusebox

Looking for a licensed electrician to install three Kogan LED ceiling lights—one in the bedroom, one in the living room, and one in the garage. I also need a small repair on a power point where the cover has come loose (just needs replacing), plus one outdoor ceiling light replacement. All lights will be supplied.

Need a cover for an instant gas water heater. Photos of the heater are attached and approx dimensions are L 1000mm x W 380mm x D 225mm. Colour needs to be Monument to match the colourbond wall and the cover needs to be breathable and easily removable. Please keep in mind the bi-fold doors. Quote to include all costs, labour and materials. Inspection required. Please come and inspect. Enmore NSW location.

Ground floor fuse has blown. Unable to locate fault. Need to systematically check all down lights and LED wall lights. Three story town house. About 27 down lights on ground floor have been affected.

Install a powerpoint.There is a box right above that I believe is active, otherwise there is a powerpoint across a doorway maybe 2 meters away if following wall. Also want a quote to install two ceiling fans. One in place of a light in ground floor bedroom, other in living room (it has downlights - no roof access but its a corrugated iron roof above) The second ceiling fan can just be via remote only. I have a ladder and can get the outlet and the ceiling fans. There is an extra photo of an alfresco that I am considering a fan for too. There is a light there - only one works

Rewire a lamp, ideally onsite.

We need our electrical board reviewed and upgraded. As well as 10 PowerPoints installed, wiring/cabling reviewed and upgraded plus a general safety review and including wiring fixed

Samsung unit. It is giving strange error and no longer seems to be turning the outdoor unit on. Flashes “E4 58” after being on for a minute or two. Has power available, already checked that.

I have a ceiling plaster rose and a bayonet fitting in the centre which is not attached to a joist beam (I had a look). I want to attach a 3.5kg brass and glass light pendent which obviously needs support. It doesn’t seem like it can be done. Anyone know how without stuffing up the plaster rose and still having it centered? The pendant hangs by a hook. See pics closely. May need hard wiring? How do we support the weight safely? There is ceiling access- pitched roof. Let me know. Thanks.

Looking for help to take down a small chandelier. Will need a ladder :)