Find a professional sink contractor near you

**Plumber needed for 2 hand basins** Looking for a plumber to install 2 hand basins in a takeaway shop in Geelong. The basins need to be installed with the required water and drainage connections, so the plumber will need to run the connections and complete the installation.

Work Required Install a new mop sink in the toilet area Set up the mop sink. Connect required water supply. Connect drainage/waste pipe. Ensure all connections are secure and leak-free. Adjust the hand-wash sink water temperature Currently, the water comes out too hot. Inspect the hot/cold water setup. Adjust or repair the mixer/temperature control so the water is at a safe, comfortable temperature. Detailed oven cleaning Deep clean the oven internally and externally. Remove grease, burnt-on food and carbon build-up. Clean racks/trays, oven door and glass. Clean around edges, seals and accessible components. Photos of the oven can be provided for assessment.

Looking for an experienced licensed plumber / commercial equipment installer for our warehouse in Glen Waverley. Work required: Disconnect and remove existing commercial dishwasher Install and connect replacement commercial dishwasher Install and connect commercial sink Check water pressure Check existing high-pressure/booster pump and replace if required Connect water inlet and drainage as required Test all connections and check for leaks Dishwasher and sink are supplied. Existing plumbing is already on site. Replacement pump, fittings or additional materials can be quoted separately if required. Commercial equipment / warehouse plumbing experience preferred.

Need a budget-friendly utility sink installed inside our warehouse, with a hose tap for washing the floor. Wastewater must connect to an approved sewer/drain—not discharge outside or into stormwater. Please inspect and advise the cheapest compliant option. Photos available.

Looking for an experienced stonemason to enlarge an existing single-bowl cutout in a 20mm quartz/engineered stone benchtop (Silestone) to fit a new double-bowl undermount sink (Buildmat Madison 775). Scope of Work: On-Site Stone Cutout: Enlarge the existing 35cm x 40cm cutout to fit the new double-bowl sink (775mm x 450mm overall sink size). Edge Polishing: Clean, smooth, and polish the exposed internal stone rim for a seamless undermount finish. Sink Mounting: Mechanically secure and seal the new stainless steel sink underneath the stone. Photos of the existing setup and new sink spec sheet are attached. Work is inside an apartment building in Ryde, NSW. Please provide examples of similar on-site stone cutting jobs you have completed.

Ceramic Sink crack repair

I need a new sink head it broke

Qualified kitchen installer - Remove and install a drop-in kitchen sink. If possible, supply a sink or give me a recommendation to buy a new one.

I have a new kitchen sink/taps that requires installation. The new sink is slightly larger than the existing sink so would require widening of the benchtop cavity slightly (wood laminate benchtops, not stone). I would also like the undersink plumbing to be configured/upgraded to allow for a dishwasher to eventually be installed.

Remove our existing pedestal sink and replace with new one. New sink will be provided by client.

I had a sink filter tap installed 2 days ago into my stone sink but it has not been fixed correctly and is loose. Also the bench top itself has been damaged. See photos. This is a brand new tap with all parts, it’s working but needs to be completed properly https://www.dropbox.com/t/1pTXCHMZz3JVkuGy

Sink has dropped from vanity table in bathroom. Needs prior experience on similar issues. All tools and consumables to be provided by you

-Install sink and tap into new bench top. -Adjust plumbing to suit sink hole location. -Replace 2x faulty shut off valves (I have put vice grips on the pipe to stop it)

My bathroom sink pop-up drain stopper is no longer working properly. The chrome stopper/cap has come off and no longer screws back onto the mechanism securely. The pop-up function also isn’t working as it should. Looking for someone to: * Inspect the sink drain/pop-up stopper mechanism * Repair and reattach the existing stopper if possible * Replace the stopper or pop-up assembly if required I’ve attached photos showing the current issue. Happy to cover the cost of any replacement parts separately if a new stopper or assembly is needed.

Plumber to install laundry sink and hook drainage up to main waste line which sits just outside. Fit off of tap too if you like.

New mixer tap installed in kitchen sink is leaking at isolation valve which has been replaced and still leaking.

My kitchen sink has just broken out of the kitchen bench and needs to be put back together. I think it was just glued in (obviously that wasn’t done well as this has happened to a lot of people in the building)

We have installed a new sink, very basic set up We need to install the new mixer + install a water filter we purchased from Bunnings Also, the sink doesn’t line up with drain pipe Looks like it needs a new S bend installed and the pipe connected up

Install a kitchen sink tap

Hey I have chipped My bathroom sink by accident and I am needing to repair.. moving out and really overwhelmed on how I can fix it as I have been advised to