Find an experienced handyman in Paddington NSW

My salon ceiling has water damage and a small section around a downlight that has cracked. The ceiling will likely need the damaged plasterboard cut out, replaced, patched and made ready for painting. Photos attached. Ideally someone who has experience with ceiling repairs and downlights. The leak has already been resolved but the ceiling now needs repair. Location: Paddington. Please quote including materials if possible. We have the paint available on site.

Task Title: Garage Pressure Clean, Storage Assembly & General Tidy-Up Task Description: Looking for a reliable, detail-oriented handyman to clean and organise a small garage/storage area. Scope of Work: 1. Pressure Wash Garage Floor & Surfaces • Pressure wash entire garage floor using provided pressure washer and cleaning solution • Ensure proper drainage is maintained and no water pools • Light wash down of lower wall areas if required 2. Assemble Storage Bench • Assemble 1 x flat-pack plastic outdoor storage bench (new, boxed on site) • Ensure sturdy and correctly installed 3. Organise & Store Items • Clean down paint tins and any dirty containers (wipe exterior, no spills) • Neatly store paint tins and related items inside the new storage bench • Consolidate and organise remaining items (ladder, tools, etc.) 4. General Clean-Up • Remove and dispose of any rubbish / packaging • Leave the space clean, tidy, and presentable ⸻ Requirements: • Must bring own tools for assembly • Experience with pressure washers preferred • Take care not to damage walls, drains, or fixtures • Ensure all work is completed safely and to a high standard

Wall mount a 60 inch Samsung tv on a gyprock wall, will require stud finder

We have an internal door that no longer closes properly — likely due to slight movement in the house and/or a latch issue. From what I can tell: - The door seems slightly misaligned in the frame (may need planing/sanding or hinge adjustment) - The latch/strike plate may not be lining up properly - The handle itself might also need attention (happy to replace internal mechanism if required, but would like to keep the existing handles) Looking for someone who can: - Adjust hinges and/or sand the door if needed - Realign latch/strike plate - Replace internal latch mechanism if faulty (I can cover cost of parts if needed) NOTE: This functional fix only - it doesn’t need to be a perfect cosmetic finish. If any sanding is required, that’s completely fine and doesn’t need repainting or detailed finishing. We’ll be renovating in the future, so priority is just getting the door to close properly. Location: Paddington Date: Must be done before end of Wed 1 April (or as soon as possibles

Need 3 simple Bunnings rollar blinds installed and drill needed

2 shower screens. Ultraclear glass 1: wall to wall. 2 pieces - 1 fixed panel( 645x2000) 1 door (625x2000) 2: above bath panel that folds in two back on itself. 400x1700 and 350x1700

I’m looking for an experienced professional to install a secure rigging point in my garage ceiling for an aerial hoop (lyra). The ceiling is solid concrete, so this will require proper drilling and installation of heavy-duty anchor points suitable for dynamic load (not just decorative use). I’m after someone who has experience with: • Installing ceiling anchors / rigging points • Working with concrete ceilings • Understanding weight load and safety requirements for aerial equipment What I need: • Installation of a strong, safe ceiling anchor (e.g. eye bolt or rigging plate) • Advice on the best hardware if I don’t already have the correct equipment • Ensuring it is safely installed and weight-rated for aerial use This will be used for aerial hoop, so safety is very important. Please only apply if you have relevant experience with rigging, structural installs, or similar work.

Front balcony of terrace. (see pic). Wood panel needs to be secured as at the left hand corner it is loose.

I recently moved out of a house in Paddington and some of the paint was chipped during the removals process. I am hoping someone can come in a touch it up. The task shouldn’t take more than 20 or so minutes.

- hang 1 x painting - hang 2 x wall sconce - repair cupboard door - repair curtain rod (pulled from wall)

Our front door is getting harder and harder to close and I need someone to fix it. It is rubbing above door lock (see photos), and seems to be slightly off kilter. I'm not sure of the best solution, but I guess it could be fixed by sanding the door or frame, or hanging. See attached photos.

Install & Set Cornice (Approx. 800mm x 800mm Section) Looking for someone to install and set a small section of cornice as shown in the photo. Materials will be provided — just need your labour and experience. Scope of work: • Measure, cut and install cornice (approx. 800mm x 800mm area) • Set joins neatly • Fill • Leave area clean and tidy (I will sand and paint it) This is a small, straightforward job but I’d like someone who has installed cornice before and can achieve a clean finish. Time estimate: Approx. 1 hour

I need a handyman to replace a kitchen tap and do a few other jobs: 1. Tap 2. Place filler or silicon in gaps around kitchen sink 3. Install 2 small latches 4. Re-screw a small bench that holds spices

Hi! I’m looking for someone to tighten a loose toilet seat. No replacement parts needed — just needs tightening/resecuring. Should be a quick, straightforward job for someone with basic tools and experience. Budget: $50 Location: Paddington When: 19th January, Monday - AM or arvo Thanks!

Fix broken sun lounge. Need to drill and secure wood in place

Outdoor cupboard door has fallen off and needs to be reattached. Hinge/ screws may be required.

We have a bookshelf that has been pulled off our gyprock wall. Looking for someone to patch the wall and rehang the shelf. Want to ensure it is secure - the screw doesn’t line up to the studs.

I need my brass handle reattached on my door

Instructions: 1) patch hole on ceiling with gyprock 2) cut out section of return air box to allow air flow into the unit 3) cut in and install 45x45 man hole into patched section to allow for access to the unit in future if required