Find a trusted local electrician in East London

One of our gates is stuck open and no longer responds to the remote, the other gate on the driveway is still functioning as normal. We do not have the manual release key and all the sensors are clean, has previously occured when the sliding gate was obstructed by leaves or debris and last repairman managed to fix in 10 minutes so seems relatively easy.

install two Japanese toilet - initially i want to check if it can be installed

I want to replace 3 on/off switches with dimmer - one of these is a 2-way hallway switch, another is in a living room and the third in a bedroom. I have all dimmable lamps, but no dimmers. I want the space around dimmer switches to be filled and finished upon installation. Install a one ceiling lamp in the living room - I have the ceiling lamp and fixing materials. (The budget is a placeholder)

A broken washing machine and a cooker and maybe help with uninstalling it

Hi there, We’re based in Hackney E9 and are looking for an experienced local tradesperson to help us refresh our small bathroom. We’d love to get an idea of labour costs and timescales before shortlisting and arranging site visits for detailed quotes. Please supply a top line estimate based on below: Scope of work: • Remove existing wall tiles and floor lino Retile: • Two walls at 70cm (w) x 170cm (h) • One wall at 170cm (w) x 170cm (h) • Floor area 150cm x 170cm • Repaint bathroom (walls and ceiling) • Refit new shower screen • Remastic around bath • Refit new light fitting • Refit new extractor fan • Hang bathroom cabinet (with lighting – power already on that wall) We’ll be supplying all main materials (tiles, paint, shower screen, fittings, etc.), but would need you to provide all necessary fixtures and fittings for installation. (NB: We may also supply our own grout, as we’re looking at coloured options.) Please could you share a rough idea of labour costs and an approximate timescale for the work? Once we have that, we’ll invite a few people to pop over for a proper look and a cross-quote. Thanks so much, Kate

Need an EICR certificate for a 2 bedroom flat

New cooker to install needs cable and connection

Removal of electric armchair & 1 IKEA tall unit with mirror door and a table top.

The tyre sensor warning light is showing on my dashboard. However, the tyre sensors have been replaced and the tyre pressure is actually fine, yet the warning light is still showing. A mechanic has indicated it is likely an electronics issue. The second issue is that the engine light is showing, this will need more investigation. The car seems to be running fine and the mechanic could not see any major issues.

Install pendant light fixture on high ceiling above staircase

Fix a ceiling light and small led light fittings

My electric hob cut out today. It is only 1 year old, brand new.

Electric radiator needs installing - wiring to fused plug and wall mounting.

Need an electrician to install one ceiling light. See picture attached of the new light and existing light. Link to the light to be installed is here - https://lightsandlamps.com/products/chelso-4-light-matt-black-and-opal-flush?variant=39901018554451&country=GB&currency=GBP&utm_medium=cpc&utm_source=google&utm_content=ppc&utm_campaign=shopping&gclid=Cj0KCQjwvJHIBhCgARIsAEQnWlAE_XFKFozzcohhsqIENajPAapn4HrYwRIyBlpUpAM8vmfE36k4e3oaAuR1EALw_wcB&utm_source=google&utm_medium=cpc&utm_campaign=kk_pmax_lights&utm_term=&gad_source=1&gad_campaignid=21062766169&gbraid=0AAAAAqy1AmNo5USEJV9gLT1guOiUGIURv

Two external lights needed to be fixed and one socket to be changed

The Problem: Hot water stopped working recently after a circuit trip Hot water runs for ~1 minute then goes lukewarm/cold System pressure is fine (topped up to 1.5 bar) ViewSmart controller is on and set to Comfort mode Heat meter shows good inlet temp (65°C) but poor output temp What I've Already Done: Checked and adjusted system pressure Confirmed KWF mode is set to Comfort Attempted power reset Likely Issues (to save you time): Based on troubleshooting, the problem is most likely: Failed/stuck PICV actuator (Item #2) - not opening properly after power cut Clogged Y-strainer on primary circuit (visible corrosion from an old leak present) Scaled/fouled plate heat exchanger What I Need: Gas Safe registered heating engineer with HIU/district heating experience Diagnosis and repair of the faulty component(s) Service/clean the corroded Y-strainer while accessing the system Test to ensure hot water is restored Access: Easy access to HIU in utility cupboard Flat is in a managed building with district heating Please include in your offer: Your experience with HIU systems (especially Evinox ModuSat) Estimated time to complete Whether parts (actuator, strainer seals) are included or extra Your Gas Safe registration number Looking for a professional who can get this sorted quickly. Happy to provide more photos or details if needed.

The existing wooden worktop is slightly too small for the new appliance. The worktop requires about 2cm to be removed from one side with an electric saw. Requires appropriate sealant to be applied around hob/worktop. The hob needs to be wired into an existing “choc block” connector by a qualified electrician in order to comply with the landlord’s regulations. Estimated job should take 2hours max.

Need an electric heater and mirror fixed on the wall

Replace 2 light switches. I will provide the replacement switches.

The previous owner of my flat has left some ceiling lights up in the bedroom and I’d just like someone to bring a ladder, unscrew and reconnect a new ceiling light. Someone who is comfortable with electrics.