Find a trusted local electrician near you

A. Survey the site with a Cap and Genny and/or other tools to identify existing cables and pipes. Refine quotation. B. Dig initial inspection holes to confirm survey data on existing cables and pipes. C. Dig a 17m trench 60 cms deep 20-30cms wide from where the pavement joins the driveway, across the left side of the drive (skirting a sewer inspection chamber) and then down the side of the house to the back gate. 1. Clear 2-3 inches of 10mm top gravel for the digging route and place to one side covered by plastic sheet. 2. Put down sheets or boards on which to store the diggings until backfilling. 3. Dig the trench: through a few inches of scalpings and then earth. Follow safe digging guidelines to safely avoid existing electrical cable, gas pipe and water pipe. 4. Instal a cable duct (provided by UK Power Networks) with a pull chord; cover the duct with pea gravel; instal a plastic warning strip provided by UKPN. 5. Refill the trench leaving access holes at both ends for cable installation by UKPN. 6. Replace the top gravel. 7. Remove excess diggings from site and leave it neat and tidy.

I was just mowing my lawns at home and almost finishing unfortunatley the plastic handle which when you press on it and press bottom triggers the machine to work got broken. Therefore, I am unable to continue using the mower.

I would like to know how much it would be to install hard wired fence lights to go along all 3 walls of our fence, and to understand if the cables would be showing etc.

I am looking for someone who can run a fuse spar and one outdoor socket for the split ac

A socket under my kitchen sink crackles when the dishwasher is plugged in and turned on so I can no longer use this socket

fitting two outdoor tubelight, replacing two old indoor tube light,fitting one ceiling light 60*60 cms and fitting a flood light . changing couple of socket and checking the triping condition and if required need to change the wiring one extension socket

All sockets in the ground floor lost power, main switch keeps tripping

my bike cuts out wen turning i know wat it is im just not a machanic

I have a few things in my house that need doing so I need a plumber/Electrition. First thing first washing machine is spazzing out because it was blocked, it needs cleaning again and factory reset. Second thing is shower water isn’t getting hot enough because there was a radiator leak in the bathroom. My husband tightened it which stopped the leak. But since then, not much hot water so I think the radiator valve needs changing.

I believe my loop in circuit is now broken and I need an electrician to fix it. A bonus would be to replace 4 light fittings.

We have a wall switch that needs fixing as the plate and switch have come off. and a lamp on the ceiling has now exposed wires

Replace old bathroom shaver socket andreplace 1 broken light (new socket and new light already purchased)

Our electric shower has just randomly stopped working and need someone to come and take a look at it urgently. I’ve bought a new shower head as I initially thought the issue might have been he hose but after installing it stiill issues - need someone to coome asap - thank you

Simple electrical job fitting 2 X wall socket.

We have taken over a commercial building and need an old by pass cable removed , plus need electrics switched back on after replacing fuses

My dishwasher is causing the kitchen circuit breaker to trip. When the dishwasher is turned on, the circuit trips almost immediately. After switching off the dishwasher at the wall, the circuit breaker can be reset and works normally. This suggests there may be an electrical fault within the dishwasher (possibly heating element, wiring, or internal component). I need a qualified appliance technician or electrician to: • Diagnose the cause of the fault • Confirm whether it can be repaired safely • Provide repair if possible, or advise if replacement is required

Need a electrician to help with a small residential job, to 3 new sockets and 6 spotlights all in same all, all will be a new installation. In the wall is only one socket at the moment.

I am looking for a fully certified electrician to disconnect and safely terminate existing 2 electrical points at our retail store on Carnaby Street, ahead of closure works. Scope of Work: Isolate, disconnect, and terminate all electrical points Ensure compliance with UK electrical safety regulations Provide confirmation of completed work if required Requirements: Must be fully qualified and certified Valid insurance Proven commercial/retail experience preferred Important: Only certified electricians will be considered Thanks

Hi, I have an unsatisfactory EICR that requires a consumer unit upgrade. The report explicitly recommends the following to clear the C2/C3 codes: ​Supply and install an 11-way Metal Consumer Unit including SPD and Arc Fault Detection (AFDD) protection. ​Supply and install a separate 2-4 way Metal Consumer Unit with SPD for the Off-Peak supply. ​Please include the necessary Electrical Installation Certificate (EIC) in your quote or mention if you can't provide.

Fix electrics in bedroom (outlet is 'hot' and zaps me when touched) and two bulbs out in the bedroom which need to be fixed / changed. Also need help hanging a small/mediumish sized mirror and a small/mediumish sized disco ball, neither super heavy. We have a ladder but our ceilings are very low so might not even be needed. Please don't offer if your price ask is going to be wildly different than what my budget is. I have not gotten the electrics fixed for 1.5 years because I have never been able to afford it as I have been out of work for 6 years and now I have this amount I have saved up which I want to use for it if possible. If not it will have to stay as is. Happy to give a glowing reference for you.