Find an experienced plumber in Coburg

Toilet 1 - gargles and when flushed, gathers water up before going down Toilet 2 - doesnt have enough water volume when flushed

Just moved house and need someone experienced to help connect washing machine safely into bench cavity.

Hi there, I’m looking for a qualified plumber to do a proper clean of the pipes at my little café. Most likely this would involve a high-pressure jet clean (happy for you to assess on site and confirm the best approach). I’ve noticed the drainage is getting a bit slow, so I’d like to get everything cleaned out before it becomes a bigger issue. I’ve attached a photos to give you a better idea of the setup. What I need: * Inspection of the pipes * Full clean/flush (jetting if required) * Advice if there are any underlying issues Details: * Location: Coburg, Melbourne * Flexible with timing, but ideally ASAP * Easy access to the areas

Need help with installation of kitchen sink and tap. Current setup as pictured. To be changed to single sink similar to photo. Current sink width 950mm, new one 1080. Need to cut cabinet top. Scope of work below. Please quote for following - Disconnent water suppy and waste. Remove existing sink, faucet and  pure water tap. Cut out bench for lager sink supplied. Cut out for pure water tap. Place in new  sink  and faucet supplied replace pure water tap. reconnect water and waste. Test water flows.

disconnect the gas stove in place and connect (second hand) new gas stove.

Rod connecting mixer tap to sink needs to be adjusted so that swivel handle turns to correct side for hot or cold water. I have removed the steel plate, rubber and bolt connecting tap to sink. Rubber most likely needs replacing.

Toilet leaking at the base

We have a loose kitchen sink tap, we've had it tightened fitted in the past, I'd say we're possibly missing a part? If someone can come, please fit/tighten this tap.

Fix pipe and install washing machine.

Outside drain needs unblocking

Cracked bathroom sink needs to be replaced

A couple of tiles on our first floor balcony have lifted a little. We'd like a qualified waterproofer to have a look under them, check th waterproofing and then replace the tiles.

I need an external valve replaced on a gas hot water unit aquamsx unit brand

I’m looking to install a dishwasher in an existing kitchen in a 1970s-built home. I’m after a licensed plumber who can handle the plumbing and connection side of the installation. I’m reasonably handy and will be purchasing the dishwasher myself and preparing the cabinetry space beforehand. The scope of work would include: Running hot/cold water and drainage to the dishwasher location Installing the required inlet and drainage connection to the existing sink Connecting the dishwasher once services are in place I’m happy to take care of any cabinetry modifications, finishing, and plasterboard repairs myself. The current kitchen utilities run through the dividing brick wall. There are also services in the roof above the kitchen, and the wall behind the cabinetry is accessible and standard plasterboard. Power is already available on this wall (currently supplying the cooktop). Overall, this should be a relatively straightforward job. I’m looking for a reliable plumber who offers fair and reasonable pricing.

Hi Daniel, We need a licensed gas fitter to check both our gas installation and hot water system, which isn't starting. Photo of HWS attached. Will let you advise cost. Thank you!

I have bought a water filter from Bunnings and have a universal adapter. However it does not seem to be able to sit perfectly on the tap. If anyone knows how to work these things, please let me know

Replaced an old 90cm gas cooktop with a new one.

I tried to solder a DIY synth, but it doesn't work. There are a few cold joints and bridges on the power header connection that need to be fixed – but my soldering is atrocious, so I don't want to make it worse and have to concede to someone with skills. This is the synth: https://makingsoundmachines.com/divskip/build/ Likely a small job for someone that knows how to solder. Happy to negotiate, but payment reflects an estimate of one hour's work. I can come to you if it's easier. Cheers!

Fit off bath. Need a licenced plumber. Waste is already run. Just need p-trap and fit off. I will have bath hob and bath correctly built at proper height

The bathroom sink completely broke. It needs fixing. Also the shower head is leaking a lot of water.