Find experienced local carpenters in Sydney

Need someone to replace and adjust hinges on two full height cabinet doors at a clients place in Surry Hills. Assume 8 hinges per door. Client says when doors where previously installed the doors opened and shut nicely, but over time they began to sag and are now hard to close. Unfortunately do not have a photo of the hinges themselves.

Strip out shelves and desk from wardrobe. The full height joinery panel on the right will need to be retained, so careful removal would be appreciated. Shelves and desk are glued, but also screw fixed to the wall and RHS joinery panel. Carpet is being removed so no need to be precious with that.

Hi guys, I need 6 tasks done in a property that is mainly joinery work that align with photos to come; - Picture 1- I have new joinery doors for a kitchen that I just need installed. New doors will need hinges cut in and will also need new handles installed - Picture 2- there’s a piece of timber flashing that needs to be fixed above the kitchen joinery - Picture 3- there’s a piece of plastic flashing that needs to be cut and glued as shown in the picture. - Picture 4 and 5- there’s 2 handles that need to be fixed to the sliding door into the bathroom in the locations shown. Please make sure the bogged areas from the previous holes are missed on both sides of the door when doing this. - Picture 6- there’s a piece of melamine board that needs a jigsaw to cut as shown in the picture and then just screwed down into the board below All equipment supplied. Just need a joiner and your tools… Cheers, Mike

Someone to come and quote on building 2 x black cabinet ends pieces like the one in the pictures below - client is installing aircon units inside them and basically need to cover them over - will need to provide guidance on cost.

I would like to have a cupboard with retractable doors built to enclose my messy laundry. Measurements approx 89.5 deep x 145 wide x 223 high.

I am looking for a experience joinery builder to build a kitchen and robe joiner. I will supply all materials and hardware. it can be built in my factory in Rydalmere (i have a cnc, panel saw & edge bander) or you workshop. I think its a few weeks work plus install time. Budget is for a onsite meeting

Modifications to Kitchen Joinery in office. Cut down slimline panytry, extend benchtop and install smal cupboards.

Cut access panels in the ceiling of wardrobes to access ducted aircon units.

Please quote your hourly rate ONLY and provide how many hours of work will be required via message. Happy to pay c.a.s.h Description of the job below - install new dimmer switches

New renovation and need a joinery for the kitchen. Fully integrated. The $200 covers a review of the drawing , site measurement and qoute. Ideally you will then make the kitchen and install in late Jan.

I have eket cabinet from ikea. I need a joinery to create a timber base and joint all these cabinet so it looks built in

I need joinery installed into a small home office space. Benchtop will need to be cut and installed to the wall using batters or L brackets. 1x drawer cabinet and 3x wall cabinets. My apartment has visitor parking available.

Cupoards built in to bedroom. 3.7 wall to wall. 0.75 height. Not sure of depth 40 to 50cm. white. Some drawers and some cuboards

Require assistance to adjust kitchen cabinet to fit fridge. a) Cabinet above fridge needs to be 5.5cm higher (indicated by red line in the photo). b) Please remove existing cabinet above fridge (including the doors. c) Cut back cabinet and doors. d) Reinstall cabinet and doors thereafter. Please see photos attached. Thank you!

Need experienced joinery with tools (eg drop saw, table saw) to help making floating frames for paintings. Experience with precise cuttings, 45° angle and bevel cuttings are preferable. I will provide timbers. Just need your help with cuttings. Drop by with your tools, help with cuttings and done. Location in Newtown. I’m flexible with time.

My son is making a simple chair out of skateboard decks for a school project. We need some fairly precise cuts made in the timber decks so they can fit together and be glued. Happy to come to your workshop if necessary.

Looking for a joiner to build a base for a baby’s cot. Mesurements are in the photos. Holes around the corners need to be on it

1. Retrofit desk in place of cubby hole and drawers 2. Add shelf to 2 cubby holes

Must have ABN. We need to cover this area (was originally a planter box but is no longer being used for this. The cover needs to be removable but also able to bear weight as we will also be requiring some wine racks (pictured) to be built and displayed on top.

Assemble joinery cabinet at office in Sydney city. Only carcass No stone install required