Find experienced local carpenters in HMAS Kuttabul

Description: Hi, I’m looking for a handyman to replace a toilet seat and remove the limescale from the bowl. Scope of work: * Remove existing toilet seat * Supply and install a standard white toilet seat (nothing custom) * Remove Limescale from toilet bowl, including stain/mineral build-up removal to restore it as close to white as possible

Undertake a small amount of cabinetry and kitchen modification works immediately after settlement. I am targeting works to be completed between 1–2 June 2026, so I’m engaging now to scope, quote, measure and prepare. Scope of works (all in attached images) • Remove existing washing machine and install cabinetry for a Fisher & Paykel single drawer dishwasher, here is the item. • Build new cabinetry drawer beneath the dishwasher • Remove small bar fridge and convert that cavity into cabinetry (shelves & doors or drawers) • There is a wall cavity currently used for artwork. Convert this into built in cabinetry; lower closed cabinetry and open shelving above • New fridge here, will be positioned in the lounge room directly to the right of the fireplace, currently where some laddered shelving sits. I'd Iike a wall or some cabinetry built to hide the fridge and make sure it does not look out of place

Assess whether the current freestanding dishwasher can be replaced with built in under bench

Internal carcass for wardrobe: 210cm high, 50cm deep. Openings are 120cm - 120cm - 60cm concept as shown below. Study: 210cm high, 60cm deep, 50cm wide shelving. 150cm wide desk. Concept as shown below. Send offers with estimated turnaround timeframe.

Involves drilling into bathroom tiles with caution, and hanging new cabinet on the wall. No pre-assembly needed.

Scope of Works – Kitchen Base Cabinet & Benchtop Replacement (Rental) Not custom • Remove and dispose of existing rotted base cabinet carcass and benchtop. • Supply and install standard flat-pack sink base cabinet (approx. 900mm wide) adjusted to fit 870mm opening.(Bunnings ) • Cabinet to be 600mm deep, white melamine interior, adjustable legs, securely fixed and levelled. • Reuse existing cabinet doors and handles; allow for hinge re-drilling if required. • Supply and install laminate benchtop with moisture-resistant substrate (33–38mm thick). • Sink cut-out edges to be fully sealed prior to sink installation. • Silicone sealing to sink perimeter and rear benchtop edge against tiles. • Licensed plumber to disconnect and reconnect sink waste, two taps, and spout. • Test plumbing and leave installation clean and fully operational.

Modify existing bottom hinged cupboard door in laundry to make into two standard hung doors. Make new trim piece around microwave and toaster shelf.

Build a custom cabinet under the window in bedroom

I’m looking for an experienced professional to sand, stain and seal approximately 30 square metres of timber floorboards at a property in Potts Point. Details: • All areas are on the ground floor • Easy access • Looking for a neat, high-quality finish • Open to discussing stain colour and finish options Please include in your offer: • What’s included (repairs, gap filling, number of coats, drying time, etc.) • Your availability • Examples of similar work if possible Thanks, and I look forward to your quotes!

I have this vintage timber bench that needs some repair. The legs are wobbly - need stabilizing. Also, while the front of the bench is finished nicely with molding, the back side of it is exposed and rough. Can anything be done to tidy it up? I already have an upholsterer recovering it later - but I just need the frame fixed before that.

After an airtasker who can cut masonite and hardboard to size.Brad nails a bonus.

I would like the fridge to be built in to the kitchen by extending the white wooden panelling as photoed. Then the fridge door will be attached to the panelling door and they will open together. I am aware I might need to buy a different fridge. I need to do this before changing the surface of my kitchen.

Must be completed by 8:30am Saturday. Tools needed. No assembly instructions have been provided so would be ideal if you have experience putting together stainless work benches or commercial kitchen benches

Hi! I want someone to complete two jobs for me please. 1. Replace cupboard doors. I want to replace the doors of an existing large purple cupboard (due to the size, these will have to be truly bespoke, not from ikea/freedom, see photo, etc) with hinged wooden doors. I want bare wood / wood veneer, so the doors can be cut from scratch from wood rather than pre-purchased from an ikea / freedom. 2. create a small laundry cupboard around an existing washing machine.

take apart a small kitchenette (includes dealing with the plumbing/ sink / tap), remove ceiling hangers from concrete slab ceiling, take away rubbish.

Hi! I'm looking for someone to make a laundry and 1 wardrobe and put shelves etc into an existing pantry for me please. The laundry is a simple job - involves building a cupboard prior (or after) a laundry install. Approx dimensions 2100 H x 600 x 700. The wardrobe would be a mostly hanging wardrobe with drawers, installed along one wall, with approx dimensions of 470 D, 3200 W and 2200 H. I'm looking for a white finish with silver handles. The property is an old building, so looking for a classic finish (rather than modern). Something like the attached photo (those doors are from freedom). I settle on the property on 4 November, so I'd like the job to be completed that week please, prior to moving in. Thanks Catherine

Small carpentry tasks to finish renovation of flat in Potts Point - gap filling, laying a few floor boards around fire place etc

We are finishing the renovation of a flat and need a hand with some small carpentry tasks for a high end finish. Floor board and ceiling trim and door hinges so that French doors open outwards

Need a quote and ideas from a carpenter to have book shelving made and installed and possibly a bookcase as a room divider.

We’re looking for an experienced carpenter to install a queen-sized wall bed (Murphy bed) that is currently disassembled. The bed was purchased second-hand and will need to be securely mounted. Scope of Work: - Create and install wooden framing to accommodate the wall alcove and ensure the bed is mounted to a flat, secure surface. - Assemble and mount the wall bed securely to the wall in line with safety and stability standards. Note: walls are made of brick (old 1920s building) Additional Info: - Location: 6th floor apartment (elevator access available for materials). - Access Window: Work must be completed between 8:00 AM and 4:00 PM, Monday to Friday (building regulations). - Materials: We’re happy to supply materials upon your advice, or you can provide them and include in your quote. Open to quotes — please include all labour, materials (if supplying), and GST.