Find experienced local carpenters in Petersham

Need 3 pieces of wood Each 80cm x 40cm Can be any type of wood, to be used at shoe shelves.

We need an experienced timber finisher / carpenter / flooring professional to sand, stain and clear-seal approximately 6 metres of raw 12 x 12 mm clear-pine tri-quad scotia. This is finishing only — the scotia does not need to be cut, mitred or installed. The goal is to get the visible curved face of the scotia as close as reasonably possible to our existing light warm-oak engineered timber floor. We tried one test section using Feast Watson Prooftint at full strength and it came out far too dark, so we need someone experienced with staining pine to properly test and control the colour before proceeding with the full lengths. We currently have: * raw Porta 12 x 12 mm clear-pine tri-quad scotia — approx. 6 m total * Feast Watson Prooftint timber stain * Feast Watson Matt Clear Varnish * 220-grit sanding sponge * timber finishing brush We believe these are the main required materials, but please advise if a timber primer/conditioner, colour reducer, different stain shade, or other preparation product is needed to achieve an even light-oak result on pine. Please include any additional material cost in your offer or discuss it with us before purchasing. Scope required: * inspect/test on an offcut first and confirm the proposed shade before completing all lengths * lightly sand and prepare the pine * apply stain carefully so it is light, even and not blotchy * apply appropriate clear matt protective coats, with light sanding/de-nibbing between coats where needed * ensure the finished pieces are dry enough to be handled and installed later Please only make an offer if you have experience with staining clear pine, timber trim, skirting/scotia or timber colour matching. Photos of similar work or relevant reviews would be appreciated.

25 mm square tube. Black powder coat finish. Looking at two of the larger pieces and one of the smaller piece. Large approx 2300mm (h) x 1000mm (w) x 550mm (d) Small approx 2300mm (h) x 600mm (w) x 550mm (d) *For both: bottom feet are 450mm (d) , racks are 300mm (d)

Need a carpenter and labourer for the whole week. Must have ABN, Insurance and white card. Work is light demo and general site work as well as wall framing

I’ve purchased timber for use as barge boards. Just need someone to install/screw into place. Easy access, small flat roofed granny flat

Licensed Carpenter required for regular work in the Inner West. A mix of outdoor and indoor work. Great client base and a good variety of jobs.

Installation of 3x wooden shelves into laundry unit to create more storage for towels and cleaning products. Shelves to measure approx. 130x65cm. Materials/wooden shelves to be supplied please.

Need someone to lay 140 width merbau boards on a newly built deck. 50% of the boards are down, just need to finish it off. Materials paid, but additional boards need picking up - approx 28x 3.2m 140 wide.

The table is 2 metres long with two half metre extension flaps; https://www.provincialhomeliving.com.au/villa-extension-dining-table-200-300-2070034 This is the product and it will still be in a flatpack, We want it a chestnut type colour (similar to the picture) but it is currently too natural/yellowy for our room.

Assemble and wall mount IKEA Metod cabinet in laundry. Cabinet will need to be installed on tiles.

Looking for some built in shelving for an area that measures 235cm high and 127cm wide with small cupboard at the bottom. Overall shape and design pictured below ( looking for a simpler version of this).

Looking for a carpenter to remove a window temporary.

I’d like someone to construct a new lifespan numbat cubby house from box. I think it will take between 2-3 hours and I will be on hand if two people are needed at any stage. I have a small backyard but enough space to manoeuvre. The cubby is about 109cm x 109cm x 140cm (tall). I don’t need the seat or fence constructed as pictured. https://www.bunnings.com.au/lifespan-kids-numbat-children-s-cubby-house_p0279763?store=7313&gclsrc=aw.ds&gad_source=1&gbraid=0AAAAADtbEB_EImvpW55b1ykIriOVRvI_l&gclid=EAIaIQobChMIyLbSv5-6igMVH6NmAh0suzuAEAQYASABEgKSVfD_BwE

I've created a bar frame and would like some help to clad it. I like the industrial look so would want someone to source wood and clad the bar. 3x photos showing the incomplete bar framework. Planks of wood forming a counter are decking planks and not secured (can be removed and replaced with a counter). 2x Inspiration images also attached showing the dark and weathered look I'm hoping to achieve but not closed to any idea that looks good. To match the building I'm after a greyed out look (not warm wood tones) Length of bar is 3.4m., height is 110cm *getting some doors on the inside (service side) would also be great.

Need cabinet doors and bottom cover installed (see picture). 1) The space underneath the sink is 70cm x 70cm. Needs two doors like the one on the left of the oven. That door measures 35cm x 70cm. 2) the space underneath of the whole thing needs a cover of the same colour and material. It measures 235cm x 12cm.

Looking for a handy person/ wood floor repairs person to urgently fix a hole in our wooden floor in our kitchen. Cut out the broken piece and replace. The appearance of the wood is less of a concern as it will ultimately go under a cabinet and sink. Size is approximately 45 cm long and 10cm across. Images below.

Repair a kitchen drawer where the 2 side pieces of wood have come away from the main panel of the drawer

Replace trimming that did not fill the gap. Some sort of timber treated pine Supply material in quote Area 5000mm by 1600mm Poor job done by previous carpenter (pls to note I did not pay for this job as you can see it was very poorly done)

Merbau timber balcony (2nd floor) maintenance; wash, sand, stain, seal. Products to be provided based on what you need. Quote for labour only

Remove car port Build timber shed/studio 3.5x4m with floor, roof, window and bifold timber doors.