Find experienced local carpenters in Sydney South

Hi, I have one wall in the living room with a water damage stain. The leak source has already been stopped/checked. Need a handyman or painter to: 1. Clean/prep the stain area, 2. Apply a proper stain-blocking primer, 3. Paint the wall with 2 coats of topcoat (I need colour matching). Cash or platform payment. Please give me your best quote. Thanks!

Description: Looking for an experienced builder/carpenter to construct 5x internal timber frame walls as marked on the attached floor plan (walls numbered 1, 2, 3, 4, and 5). Plan shows exact locations, lengths, and heights (2,335mm noted on drawing). Scope of work: • Frame and build 5x timber stud walls per attached marked-up plan • Wall heights/positions as shown in drawing • Timber framing with plasterboard/lining as required • Keep work area clean and tidy, remove all debris/offcuts on completion Requirements: • Must be an experienced, qualified builder/carpenter with proven timber wall-framing experience • Please share photos of similar past work when applying • Own tools and equipment required • Please review attached floor plan carefully before quoting — quote must reflect the full scope shown Important: • Please quote a fixed, all-inclusive price covering labour AND materials • We are not anticipating any additional costs — please factor everything into your quote upfront (materials, waste removal, etc.) • No parking available on-site

2x carpenters or experienced handymen to remove old ceiling grid system 12m2 then frame out 3x ceilings 20m2 and 1x small hideaway room 2000x1500x1500, this room will need a sheet of plywood installed and will take about 1-2 hours to frame as it’s a bit tricky with pipe work -Ceiling height 3000mm -Timber supplied -You will need your own tools and ladders -loading zone parking outside -11am or after start time Sunday 12/7/26

I am looking for someone to create and build a fish tank cabinet. The fish tank is 60x45x45 cm, but the cabinet door must be on the 45 cm side, as the side view is on the 60 cm side. Weighs at 120kg.

Cabinet Repair Assessment Required I’m looking for a professional to conduct an on-site assessment for 4 damaged cabinet door and surrounding area. The assessment should include: - Inspection of the damaged cabinet and repair area - Accurate measurements of the affected sections - Identification of the repair work required - A written quote with detailed cost breakdowns for labour and materials - Estimated timeframe for the repair work Please reach out if you are available for an on-site inspection and written quotation.

In Barangaroo (2000), build a cabinet in apartment block

Hi need you to build a cabinet with limited instructions and no pictures. Instructions: https://drive.google.com/file/d/17amzxT1q4KwWh7fBrcX4LiK427RzVOn6/view?pli=1

Cabinet maker needed for a few jobs around the house. Happy for these to be completed at different times if needed. Please see photos numbered per job: 1. Convert these 2 kitchen drawers into a single, deep drawer. 2. Replace these entry drawers with a cabinet door and white laminate shelves inside. Plywood finish is fine for the door as it will be rendered eventually. 3. Replace this round tabletop with a ‘kidney bean’ shape that marries the curved bench, plus make another larger tabletop that would marry the first one, to achieve a secondary table (no legs required as I will be doing that myself). Both tabletops must be laminate finished. Ideally I’d pick the finish but if it can only be white that’s fine. 4. Create a small plywood box to cover the pipe under the sink. 5. Add a plywood or gyprock trim to hide the gap between the wardrobe/cabinets and ceiling (one kitchen cabinets plus two wardrobes -one is the one pictured plus one smaller one). If you can’t do all the jobs, please specify in Your quote which ones are you quoting for. Thank you!

I need a freestanding timber breakfast bar and 2 stools for my apartment. I’m a bit flexible on the design of both the breakfast bar and stools but would like something with sled legs - similar to the pic attached - but it will be on carpet so if a crossbar is absolutely necessary to keep it sturdy, that’s ok. I’m flexible on the type of timber as I will distress it in similar way to the drawer shown in the pic so I’m not looking for crazily-expensive timber and it only needs to be properly sanded but not varnished. It needs to be sturdy enough to lean on when eating or working on light tasks. Finished dimensions 1300W x 500D x 1000H. Stool dimensions to work with this. I would like a rough drawing to show me the plan for the breakfast bar and stools with dimensions and specifying the timber to be used.

We require assistance with creating fixtures to attach torches to a wall mount in our office. We also have some current fixings that require attention.

I need a repair for a wooden bed frame where two of the legs have broken off at the corners. • Fill/Reinforce: The corner joints need new wood blocking/fillers to replace the damaged areas.they are attached to leather bed frame so need careful attachment. • Secure: Drill new pilot holes and re-mount the legs so they are structurally sound.

We need tradies that all multitasking around the field of handyman carpentry plenty of work Sydney We need tradies that know what they are doing own tools and transport sub contractors a lot of work to be done Sydney areas

Hi Taskers, I need a custom-made plywood box built to the following specs: Dimensions Length: 200 cm Width: 50 cm Height: 90 cm Construction Details Material: 18mm plywood All sides to be flat and flush Bottom is open (sits directly on the floor – not visible) Two hand cut-outs (one on each end) to make lifting/moving easier Approx. size of cut-outs: 150 × 50 mm (or standard comfortable size – open to your suggestion) Needs to be strong, neat and stable, suitable for indoor use What I Need From You Cutting, assembly, and finishing (light sand; no paint required) Supply of materials Delivery to my place in Camperdown

Title: Handyman Needed – Fix Cabinet Backing & Table Tennis Leg Description: Looking for a handyman to do two quick jobs at my club: Cabinet Backing: The core flute has come loose. Needs to be securely reattached so it doesn’t pop out again. Table Tennis Table Leg: One leg needs fixing. I have the screws ready. The brackets need reinforcing with additional screws and washers on the outside. Bigger screws can’t be used, and simple filler/resin won’t work. Both jobs are straightforward for someone experienced and can be done together. Requirements: Must know how to reinforce fixtures properly. Bring any small tools you might need (screwdriver, drill, etc.) Efficient and reliable Expected time: 1.5–2 hours. The job needs to be complete on a Wednesday between 12-4pm for this to work. I've included a $30 parking fee.

We need tradies that know what they are doing own tools and transport sub contractors a lot of work to be done Sydney areas

Need an experienced carpenter to build in a door to empty space and put in hinges and a door handle

Need someone to fabricate a Stainless steel snorkel for my Nissan Pathfinder R50 2003 I can come to you anywhere 2 hours from Sydney

Busy building maintenance company seeking the services of a semi retired LICENSED builder or carpenter to assist 2-3days per week ongoing. We’re after an older gentleman (aged 55+) and will provide an excellent package for the right person - please no handymen need apply

I am located near Macquarie Centre / Macquarie Park and would like to request a quote for a bathroom cabinet repair. As shown in the attached photo, the side panel of a bathroom cabinet has water damage at the bottom near the floor. I am looking to have the damaged section repaired. Please let me know: An estimated cost range Your availability

Need help buidling a custom shelving unit at a small bar in darlinghurst