Find experienced local carpenters in Camperdown

1. Hinges replaced on a large cabinet door flap. 2. A drawer installed from scratch in a section of the kitchen wall that might be a bit tricky because it is below the floor boards in the dining room. 3. Another drawer installed to match existing drawers (completely unrelated to number 2). I have the front plate already because it is used for an ironing board that was never utilised. So we want the storage instead. - Due date: Flexible

Water stain from plant has left a mark on the floorboards. - Due date: Flexible

Built in shelving either side of fireplace with curved front Built in storage under stairs - open to design and whatever works best - Due date: Flexible

Replacement / reinstallationof skirting boards after replastering and damp work - Due date: Before Friday, 20 October 2023

Complete several woodworking jobs on new kitchen. Finish pelmets, side of dishwasher completed and box in fridge. All materials here - Due date: Needs to be done on Monday, 9 October 2023

Built in wardrobe design and install needed L3450 x H2080 - Due date: Flexible

Non - existent door jamb & no lock previously because changed from hinged door to a sliding door - Due date: within a week

I'd like to replace a chip-board Ikea bookcase that sits against a wall on carpet (& can tip forward) with a built-in unit of the same capacity. The current bookcase measures 205cm high, 80cm wide and has a depth of 28cm plus 2cm for the glass doors (which I like to keep dust out). It has five shelves of varying height. I'd like it to be made of solid wood of a light colour or painted white.

I have a stainless steel hall table that is too high and I’m wanting to saw off about a foot from each leg to make it a coffee table. I’ve tried to saw with a hacksaw but I can’t get the lines straight/even, so I suspect someone with experience and preferably a power tool is needed. You can see on the pictures where I have placed tape to show the new height. The metal legs are 1 inch x 1 inch, unsure of thickness but it is hollow. I need the cuts to be even and straight. - Due date: Flexible

Various jobs for this project - cladding reception desk, building floor to ceiling cupboard doors etc - Due date: Needs to be done on Friday, 9 June 2023

I have a stainless steel hall table that is too high and I’m wanting to saw off about a foot from each leg to make it a coffee table. I’ve tried to saw with a hacksaw but I can’t get the lines straight/even, so I suspect someone with experience and preferably a power tool is needed. You can see on the pictures where I have placed tape to show the new height. The metal legs are 1 inch x 1 inch, unsure of thickness but it is hollow. I need the cuts to be even and straight. - Due date: Flexible

Kitchen Benchtop Notch Cut-Out. - Due date: Needs to be done on Saturday, April 22, 2023

Minor damage on drivers passenger side. I need a quote to repair the panel. - Due date: Flexible

I need someone to: - remove my existing IKEA shaving cabinet with mirror (I can dispose of the current cabinet, see picture of existing cabinet) - put together and install a new IKEA shaving cabinet in its place, screwing it into the wall (it's the ENHET 1 door cabinet) - hang 1 mirror onto a wood wall Job is in Camperdown, dates are flexible. - Due date: Flexible

Need my cabinet extended so i can fit my new fridge in it. Thank you

Wooden handrail install for staircase required approx 4.5m Materials not supplied - Due date: Flexible

Looking for someone to install 50 lineal metres of stainless steel wiring to a new timber balustrade. I have constructed the balustrade which is a structural part of the deck. The balustrade will be 1m in height from finished deck level which will include a 45mm capping piece. the first straight run is 3.4 lineal m long and the second run which is a return is 2.2 long. all posts are 1.1m apart and set in concrete as a subframe support on the bearer straight up through the deck. happy for different price ranges but the price would be for supply and install of wire , saddles and turn buckles etc

I have the wooden base of a piano frame, the wood needs cutting at the joins, with a power saw that will go through 100ml thick wood. must be vaccinated and wear a mask due to health reasons. Due date : Monday midday

I need two carpentry jobs done: (1) raise a shelf above a fridge a little bit higher (2) replace a small wooden step by removing existing timber and rebuilding with hard wearing timber - Due date: Needs to be done on Monday, 20 June 2022

Installation of kitchen cabinetry on site - Due date: Flexible