Find experienced local carpenters in Marrickville South

This kitchen bench made of wood from Bunnings needs to be cut down one side so it is 100 cm long. Right now I think it’s 120.

Hi, I need a skilled carpenter to build a ramp which would sit on 2 steps inside our house. See attached photo. The width is approx 88cm, and the steps are approx 13cm (each) high. This is not for a wheelchair, it’s for our dogs which have back issues, but my husband and I (he’s 100kg) needs to be able to walk on it too. The gradient would probably mean the ramp is around 80cm long. I’m looking for one singular piece, which is staggered to cover both steps. The ramp needs to be non slip and have non slip base. I don’t want it to be permanently fixed though (able to move for cleaning ect), but when in place, for it not to move. If you’re up for the task it would be great if you could come and measure etc first. Thanks!

I need 8 small ramps made from wood. The ramps are for steps for my dogs (which can’t use stairs due to back issues), but will also need to be able to take the weight of a human (110kg). The ramps are not permanent, more so solid enough to stay put (perhaps with some non slip mat under neath). The two areas are: 1) outside. There are two steps and I require 6 ramps in total. A) For the top step the approx measurement is 15cm high, 23cm deep, and 88cm long. I need 3 ramps this size. These ramps will sit on the stair itself. B) for the bottom step (where you step up from ground level) the approx measurement is 20cm high, 34cm deep and 88cm long. These ramps will sit at ground level and be pushed up against the step. The material needs to be suitable for outside. The ramps need to be lacquered / stained. 2) inside. There are 2 steps and I require 2 ramps in total. A) for the top step the approx measurement is 13cm high, and 25cm deep and 121cm long. I require 1 ramp this size. This ramp will sit on the stair itself. B) for the bottom step (where you step up from ground level) the approx measurement is 14cm high, 25cm deep and 121cm long. I require 1 ramp this size. The material needs to be suitable for inside. This ramp will sit on the ground level, and be pushed up against the step. Both ramps need to be lacquered/ stained. The task would involve a measurement on side to ensure all dimensions are correct (Marrickville), and the completed ramps made and brought back to the house no later than 2 May. I have attached pictures of the 2 steps inside, and the 2 steps outside. THANK YOU!

Looking for someone with a drill suitable for stainless steel to install this bolt on our dishwasher to stop the door from opening.

The back of my wooden outdoor lounge cracked and i need someone to screw it back together. Might need a super glue for some parts as it is prone to cracking

Our kitchen cabinets are high and deep making them awkward to organise and access. We'd like to add additional shelves to them to make them more useful. We’d also like to add more shelves in our wardrobes if possible too. Flexible on budget, I understand material and labour costs will vary. For the kitchen cabinets - looking at adding a shelf to the lower section to split it out a bit Main bedroom - adding shelves next to where the little flat pack one is now Bedroom 2 - add shelves where the vacuum is currently with enough space for the vacuum to go next to it if possible. Open to any suggestions and ideas :)

stain deck and top of deck seats the deck (including 2 seats) is 2.7 meters x 3.5 meters (I have about a third of a can of Cabot’s stain) replace 1 small ikea shelf with a new one Replace 6 ikea shelf brackets Touch up paint on 2 door frames Fix bedroom door handle so it closes properly

I have 5 stained glass windows with smallish clear glass panels. I need these clear panels exchanged for opaque glass panels. I can supply the opaque glass but you'll need to cut and install it. Only artisans with experience in stained glass/lead light need apply.

Just bought a shelf has to be drilled into the fridge , screws are supplied just need drill and experience.

Supply and install new timber handrail for internal staircase in townhouse. Estimated total combined length is 5.5m.

Need to repair my wood table top due to burnt

Need install stainless counter and water pipe under sink (already have old pipe just reinstall the new stainless counter then connect the pipeback

Need a timber fusebox built and installed on an outside brick wall 1020 x 660 x 100

I have this ikea bed that I need to be stained/varnished. It’s brand new and hasn’t been assembled yet so it’s the individual pieces that need to be finished. https://www.ikea.com/au/en/p/glamberget-extendable-bed-w-stor-2-mattresses-pine-agotnes-firm-s39568384/ I would do it myself but we don’t have the space! Photos are an example of the colour we’re after.

We need to try and remove a large grease stain from our recently grinded and polished concrete floors in a warehouse.

I have a custom built hanger that I need drilled together. I've pulled it apart and put back together many times, it's not super tricky. I'd also love to get a table top sanded back. It's roughly 1.8m x 0.7m. Love a quote for hanger assembly only and both together if possible. Thank you!

Remove burn stain from white particleboard wood cupboard . Materials - Particleboard, Plastic edging, Acrylic paint,

I need an unmade ikea pine bookshelf stained slightly before having it installed. 2x wide units and 2x thin units

Bought ikea furnature and it came unstained (different than display model). After a medium to dark look. Not to fussed about any particular shade. It just currently looks like unfinished furnature. Want it to look done.

I have kitchen cabinetry which I’m looking to reorganise to facilitate installation of dishwasher (standard 60cm wide etc.). Not sure if this is built in or free standing as yet. It also needs to be installed under Caesar-stone bench top.