Find a professional local carpenter in South Lambeth

The worktop of the wooden table was damaged by putting a hot pot on it. The damaged area has roughly length of 20cm. - Due date: Flexible

We have a broken wooden trellis (approx. 6 meters long and 80cm height) that needs replacing in the garden and then the pant attached to this trellis needs trimming. - Due date: Flexible

We want a brick wall built in our garden for a bench and a raised bed. Total length is about 3.3m. We have the bricks and slabs for the bench. - Due date: Needs to be done on Tuesday, 30 August 2022

Concrete resurfacing of a set of 7 outdoor steps (~3.6m2 surface area) The current ones are cracked, chipped and uneven (see first 2 images). Ideally would like them to be refurbished to look like the upper level steps (see last image) - Due date: Flexible

I would like the bin store doors taken off and opened up. Please neighbours vs mine. Would require wood to be taken a way also. - Due date: Flexible

Hello, We need repair of our two seater sofa. I believe the springs and underlying support have given up. When we sit on sofa, especially in the middle, we sink in. We are seeking someone who can repair this without damaging the sofa. - Due date: Flexible

Need to cat proof my patio (preferably with bamboo fencing), need to bring own materials - Due date: Flexible

We ve been flooded, so the adjoining wall to the tall kitchen cupboard has swollen, pushing the piece of wood filling the gap between the cupboard and the wall and eventually making the cupboard sides too narrow... so there is not enough space on the sides of the front panels for the drawers to close or the door

Inclusive of materials White satin plywood 2 door storage unit H165cm W76cm D45cm 4 shelves (measurements tbc) - Due date: Before Tuesday, 1st Mar 2022

I have underlay and carpet in my guest bedroom that needs to be refitted. I needed to build up the skirting boards which were too high and the gap between carpet and skirting board was too big. I bieve the majority of work is done, just needs to be finished off. I also have underlay down in the hallway and need the sisal to be fitted. Same as above, have had to build up the skirting boards. - Due date: Before Thursday, 16th Dec 2021

Plumber cannot open boiler to service it. Need to remove the piece of wood that's blocking access (marked with an X in the first photo). Then widen the existing square access panel to the same width as the cupboard door (see second photo), so that the boiler cover can be removed/opened. It needs to be a neat job please. - Due date: Flexible

I have a double IKEA loft bed that needs some modifications to suit my room, which has a relatively low ceiling. The legs (See markings) need to be cut off by about 35cm. Similarly, the ladder needs to lose a step or two. Another thing I need is for the ladder to be installed across the width of the bed (See arrow in picture), rather than the length as provided by the. For this, the wooden pieces in the frame need to be cut off and holes need to be drilled accordingly to fit the nails provided for ladder installation. By the way, it has not been installed yet, so all the work needs to be done on separate pieces. I am intending to install it by myself once all the work is done. If you could let me know how much the works would cost, that would be wonderful. Thanks!

UPDATED 24/8. Reposting this with a smaller scope after receiving advice from Airtasker. Our front door weather bar/strip needs replacing (it is in poor condition to weathering). Task is to remove the old bar and install new weather bar, which we will provide (unless handyman wants to supply). No painting needed. I've provided an indicative budget assuming the work will be completed within a couple of hours. Must have carpentry skills. Looking for job to be completed this week (between tomorrow and Friday).

Description: I have a Be Quiet dark base 700 which looks amazing and perfect for me but the airflow is very limited, mostly only air flow at the back. I would like to add airflow to the top and front of the case but would like it done by someone with experience i.e. with proper tools and know-how, as I want it to still look good after making holes or cutting out parts of the top or front of case Is this something you can help me with? See photo attached of exactly what I would love and photo of existing case how it is at the moment. See some links of examples on how this is done. Anything like this I would be happy with. https://youtu.be/stysHOBOfvk https://youtu.be/QvypJFvsPW0 https://youtu.be/64k-Ms5w_7E https://youtu.be/2rxjm3IsLzY I have all the parts just need someone with the tools and experience to make it work. I have the grill vents, (nuts and bolts) and some dust filters.

Description: I have a Be Quiet dark base 700 which looks amazing and perfect for me but the airflow is very limited, mostly only air flow at the back. I would like to add airflow to the top and front of the case but would like it done by someone with experience i.e. with proper tools and know-how, as I want it to still look good after making holes or cutting out parts of the top or front of case Is this something you can help me with? See photo attached of exactly what I would love and photo of existing case how it is at the moment. See some links of examples on how this is done. Anything like this I would be happy with. https://youtu.be/stysHOBOfvk https://youtu.be/QvypJFvsPW0 https://youtu.be/64k-Ms5w_7E https://youtu.be/2rxjm3IsLzY I have all the parts just need someone with the tools and experience to make it work. Have the grill vents, (nuts and bolts) and some dust filters.

I need to remove a built in single door fridge to replace with a taller free standing fridge. to so do I need the worktop cut shorter and finished alongside the bottom MDF to be cut shorter as well.

Hi, we need to oil a wooden decking (~40 sqm). Equipment required: anything you need to complete the job. we have no tools and no oil/paint