Find experienced local tradies in Sydney Eastern Suburbs

Looking for a licensed electrician to fix electrical fittings after an internal wall demolition. I need the following reinstalled and connected: Refix 2 power points. Refix 1 light switch. Test the circuit and confirm everything is working correctly. Ensure all work is compliant and provide a Certificate of Compliance if required. The wall is already open, so all wiring is exposed and easily accessible. No wall chasing or demolition is required. Located in Bondi Junction. Please quote including labour and any minor materials required. Licensed electricians only.

I need a licenced electrician to move power point 10 cm to the left on a Gyprock wall, another removed from the skirting of a built in wardrobe and two landline phone points removed. Photos in order below.

Patch ceiling and install a small drip tray and insulation. The main roof leaks into here we have it solved but need to put in a small drip tray (Where the stained picture is) Hot water heater style) and some reflective insulation and seal up. I’m happy with patching or replace entire sheet. Budget is flexible I just want it done with a clean finish. House with driveway easy access 8ft ceiling height. Will need some discussion on site.

After a quote to hardwire in a Harvia wall-mounted electric sauna heater (4.5kW) via an already existing dedicated 20A outlet. The laundry runs off a 20A breaker. The circut can be a will be a dedicated circut and run the sauna on its own. Its a few meters away from the sauna. Harvia wall sw electric sauna heater 6kw https://sdsaustralia.com/product/harvia-vega-bc/

Insulation & Gyprock Installation – Garage Studio Conversion Looking for an experienced gyprocker/plasterer to help finish a garage-to-studio conversion in Sydney. Scope of Work * Install wall insulation to all external walls. * Install ceiling insulation. * Supply and install plasterboard (Gyprock) to walls and ceiling. * Set and tape all joints. * Apply topping compound and sand as required, ready for painting (Level 4 finish preferred). * Cut-outs for downlights, speakers, power points, air-conditioning penetrations etc. Room Details * Studio is approximately 20m² floor area. * Rough dimensions shown in attached sketch. * Three external walls and one internal wall. * Split-system air conditioner will be installed as part of the project, so coordination around pipework penetrations may be required. * Existing framing is in place, although some sections may need packing/shimming as walls are not perfectly straight. What I’m Looking For * Experience with insulation and gyprock installation. * Own tools and transport. * Ability to advise on materials required. * Please quote separately for: 1. Labour only (I can supply materials). 2. Labour + materials supplied. I’m happy to purchase materials myself if that works out more cost-effective, and can arrange delivery to site if required. When Flexible over the next few weeks. Please include: * Relevant experience/photos of similar work. * Estimated timeframe to complete. * Whether your quote includes materials, rubbish removal and setting/sanding. Attached is a sketch of the room layout and dimensions. Budget: Open to quotes. Please provide your best fixed-price estimate after reviewing the sketch.

2 holes on plaster board to be repaired And 5 dents to be filled Filled and painted white

I’m looking to have someone repair and re-render a small facade which is approximately 3000mm high by 5500 mm wide. Note that part of the facade is already painted and the area across the top to the garage door is marine ply. I have a few length of corner bead on site.

Small hole made in wall. Need it filled and fixed. No need to paint. Just repair it

Site inspection and preparation * Supply and install moisture-resistant Gyprock ceiling sheeting * Reinstate ceiling section and secure to existing framing * Tape and set all joints * Sand and prepare surface for painting * Apply sealer undercoat and two finish coats of ceiling paint

Unfortunately, my 75-inch TV fell off the wall. I have some holes to fix. It’s a bit tricky, as the wall is gyprock. The holes are small, but I am assuming there will be filling and painting involved. Thanks

I was installing a TV bracket when one of my power circuits started tripping. When the breaker is reset there's an audible "popping" sound, strongly suggesting a drill bit or screw has caught a cable behind the wall. Breaker is currently isolated and labelled off. What I need: • Diagnose and confirm the fault • Repair the damaged cable to AS/NZS 3000 standards (accessible junction box or rerun as required) • Insulation resistance (megger) test the circuit afterwards to confirm integrity • Issue a Certificate of Compliance for Electrical Work (CCEW) Site details: • Switchboard: modern Clipsal MAX9 with individual RCBOs per circuit — the affected circuit can be fully isolated without disturbing the rest of the house • Strike location: behind a heavy-duty articulating TV bracket. A light switch directly below the bracket suggests the cable is on a vertical run from that switch • I can remove the TV and bracket before you arrive, or leave it for you to drop — happy either way • ⚠️ Important: the wall is finished in a bespoke Monaco Grand Prix poster wallpaper that cannot be easily replaced or matched. Please plan to make the smallest possible access cut, and factor minimal wall disturbance into your approach. I'll handle wallpaper/plaster make-good myself afterwards. What I need from your quote: • Licensed electrician only (please include licence number) • Breakdown: call-out, labour estimate, materials, CCEW • Whether you'd splice in an accessible junction box behind a flush cover, or rerun the cable to the nearest accessible point • Earliest availability — not urgent but want it sorted this week Happy to send through additional photos of the bracket, switchboard, and likely strike location on request.

Super quick job - my tools are in storage Just need one 8-10mm diameter hole drilled through an internal gyprock wall - so I can run a small hose through it (wall approx 75mm wide) Power point availalbe if your drill needs Easy access to house (park in driveway) You'll be in and out within 5-10 minutes

Quote on plastering job in Coogee

Looking to get my dining room walls re-plastered or white set. Room is approx 3.3x2.5 for scale, three walls as pictured, no ceiling. Two base coats and one top coat. I’ll sand and paint. Preference is for as soon as possible so let me know your availability in your offer.

I have purchased the Otti oak laundry cabinet, countertop, sink and associated hardware. Need a tradesman to help install. Current sink will need to be removed and any plumbing that may be required also. I would also like advice on a sliding door while doing the job. But I don’t have this yet and not sure what best option would be. Laundry is on the deck of my house. External but under cover. Any questions before sending an offer please let me know. Technical specs are here; https://www.templeandwebster.com.au/Byron-Natural-Oak-Laundry-Cabinet-with-1300mm-Extended-Carrara-Countertop-and-Sink-OTTI1242.html

I need a confident handyperson to hang a Rachel Donath Dora Gloss Mirror — a premium fibreglass mirror (70cm × 95cm, 17kg) — on an internal pebbledash render wall. The mirror uses a French cleat hanging system (wall cleat + mirror cleat). The wall cleat needs to be fixed securely into the masonry behind the render. 📦 WHAT’S SUPPLIED: • The mirror (already delivered, in box) • French cleat bracket (included with mirror) • Screws (included with mirror) 🛒 PARTS TO PURCHASE (reimbursed on receipt): Before arriving, please pick up from Bunnings Rozelle (Mullens St, Rozelle): • 4 × M8 heavy-duty masonry anchors (Fischer FUR M8 or Ramset Dynabolt M8) • Estimated cost: ~$20–25 (fully reimbursed) 🔧 TOOLS REQUIRED (please bring your own): • Hammer drill with masonry bit • Spirit level • Screwdriver • Measuring tape • Cable/pipe detector ⚠️ WALL NOTES: The wall is pebbledash render over brick. Anchors must drill through the render and at least 50mm into the brick behind. Standard plastic plugs are NOT suitable — this is why we need the upgraded anchors above. ✅ JOB IS COMPLETE WHEN: • Wall cleat is fixed level and securely into the masonry • Mirror is hung and stable • No cracking or damage to the surrounding render 📬 Please include in your offer: • Your experience with masonry/render walls • Whether you have all tools listed above • Your total price (labour + parts reimbursement)

Need a tradie with public liability insurance to install my ANKR bike anchor to an outside masonry wall. Please confirm you have insurance in offer.

We need 3 medium sized framed prints hung on plasterboard walls

I have a 4.4m x 2.7m wall in a bedroom that needs to be white set rendered prior to painting. Please include in your quote, a rate per 10sqm in case there are other areas that require the same. Please also include advise the cost to cover and white set over the following vent.

My salon ceiling has water damage and a small section around a downlight that has cracked. The ceiling will likely need the damaged plasterboard cut out, replaced, patched and made ready for painting. Photos attached. Ideally someone who has experience with ceiling repairs and downlights. The leak has already been resolved but the ceiling now needs repair. Location: Paddington. Please quote including materials if possible. We have the paint available on site.