Find professional kitchen drawer repair near you

Looking for someone to replace two kitchen drawer fronts. I already have the replacement fronts ready to be installed.

Quote Needed: Custom Garage Storage and Kitchen Drawers Looking for separate quotes for the two attached garage storage designs, including sliding doors: Design 1: Full-width storage unit Design 2: Shorter, lower-cost alternative If Design 1 is too expensive, we may proceed with Design 2. Please quote materials, labour and installation separately for each design. I would also like another separate quote for four kitchen drawers. Approximate available space: Width: 25 inches Height: 13.5 inches Depth: 21 inches Location: Bellbird Park

Looking for a carpenter or cabinetmaker to finish installing two internal pull-out pot drawers behind existing cupboard doors. Work required: - Complete timber spacers—45mm base blocks are already securely installed for one drawer. Add 19mm facing panels using screws only, no glue. - Fit two pairs of Kaboodle 450mm soft-close runners, set back 18–20mm to clear the closed cupboard doors. - Cut the supplied white melamine panel into two drawer fronts, each 445mm high × 540mm wide. - Attach front brackets, fit the pre-made drawer boxes and adjust for smooth operation. Cupboard dimensions: 550mm wide × 550mm deep. Planned 64mm spacers provide clearance around the existing hinges. All materials and hardware supplied. Please bring cabinetry tools, including a fine-tooth or track saw for clean, chip-free melamine cuts.

I have the front of the drawer but need to build the drawer

Kitchen drawer fixing harn lock tracking system

Drawers and faces are okay, it's the hardware that connects both that needs replacing/repairing. Hardware is Blum Metabox drawer system, with METABOX front fixing brackets which screw to the back of the drawer face and lock onto the front end of each steel side. On the drawer that’s still together, the bracket has a screw going through the drawer side into it. That looks like the standard screw-fixed type, not Blum’s tool-free CLIP version. So the likely part is: ZSF.1700, sold as a left and right pair. Lincoln Sentry lists it as the screw-on front bracket that fixes to the drawer side with a screw, suiting M, K and H height drawers. If your sides turn out to be the low ones, you need ZSF.1510 instead. It suits N height (54mm) drawers. If they’re the tool-free kind after all, the part is ZSF.1200. It’s the CLIP version of the bracket for M, K and H heights. lincolnsentry To check the height, measure the steel side from the drawer bottom to the top edge. Roughly 54mm is N, 86mm is M, 118mm is K and 150mm is H. Your sides look like M or K, and both take the ZSF.1700. These brackets are cheap, a dollar or two each. Lincoln Sentry stocks all three; take your old plates along and they’ll match them by eye. Not sure which it is, but supplier for Lincoln is in Varsity Lakes Lincoln Sentry 3/481 Scottsdale Drive Job is to replace all these with new fittings in an apartment in Surfers Paradise. There are also 4 other drawers in the kitchen with similar, so depending on price, open to including those as well.

Hi, I need help fixing a wooden drawer that isn’t sliding smoothly and levelling/adjusting a bathroom door. Please let me know if you can do both jobs and provide a quote. Thank you

Kitchen drawer slides open after closing, even when empty. Need inspection and repair. Budget includes call-out and labour. Any replacement parts must be approved separately.

The roller has come off one of our larger kitchen drawers and now I can’t use it. Need that roller replaced, and maybe some general adjustments to the drawers to get them level.

Kitchen drawer is unable to close properly. The soft-close sliding rail or click-lock mechanism appears to be stuck or damaged. Need someone experienced to: * Inspect and repair the drawer runners. * Realign the sliding rails if needed. * Replace any damaged parts if necessary. * Make sure the drawer opens and closes smoothly. Location: Research VIC 3095 Please bring your own tools. Photos attached. Looking for someone reliable who can fix this as soon as possible. Thank you!

I have a kitchen drawer (soft closing) where the screws to the runner have come loose and the runner (or bracket?) has come away from the inside of the drawer. I have pulled the drawer out but need someone to reattach the runner/bracket and (and maybe tighten the one on the other side, the screws look a bit loose) and reinsert the drawer. I have the four screws that have come out but the exiting screws have left a bit of a hole (see pics). Must be able to do a professional job as it’s not my kitchen :)

Facing on kitchen top drawer has come away and needs fixing

We have recently had an under-sink water filtration system installed, which means the existing drawer behind the cupboard/drawer front can no longer be used. I would like someone with cabinetmaking/joinery experience to: • Remove the existing drawer front from the drawer mechanism. • Refit the existing front so it sits in exactly the same position and maintains the existing gaps/alignment with the cabinetry. • Ideally convert it into a hinged/drop-down solution. • Supply and install the necessary magnets, catches, hinges or other hardware. • Ensure it is secure but can easily be removed/opened when access to the water filtration system is required. The main priority is for it to look exactly as it did previously when closed. Existing drawer front and cabinetry are all in good condition. Photos available. Looking for someone experienced in kitchen cabinetry/joinery who can achieve a neat, professional finish.

Fix three kitchen drawers 2 have the cupboard face come off, one is misaligned.

Need handyman or woman to help fix kitchen drawer. The drawer has refused to close

Hello, We are looking to have a small utensil drawer installed in our kitchen in Meadowbank (Ryde area). The drawer would sit directly above our small microwave oven, inside the current microwave enclosure. The new drawer cutlery drawer would be done in the style to match the existing drawers. As part of the job, the facia around the microwave oven enclosure would need to be removed as it clashes. Additionally, the power point inside the microwave enclosure, may need to be moved downwards by about 150mm. I have supplied photos, and a concept sketch of the proposed cutlery drawer. We would like to have someone come out and visit us on site, and measure and quote for the design. We are looking to have the job done in the next few months. We have in mind a budget of somewhere in the order of $1, 000 to $1,500 for this task. Regards, John Drake.

My kitchen drawer front has come off and needs to be reattached properly. The drawer runners are still attached, but the drawer front has detached from the drawer box. It may need the existing brackets adjusted or replaced if damaged. I've attached photos showing the current condition. Looking for someone experienced with cabinet or kitchen drawer repairs who can: Inspect the drawer Reattach the drawer front securely Replace any damaged brackets or fittings if required Make sure the drawer opens and closes smoothly Please bring any small screws or replacement fittings that may be needed.

I need two identical drawers built and installed into a cavity where an old dishwasher was removed. Cavity is 800mm (H) x 600mm (W). What I have: • Two white painted timber drawer fronts (they will need to be cut to size) • Two wooden handles to be screwed on What’s needed: • Build two drawer boxes — bases and the missing side panel cut to size and squared up • Source and supply all materials: drawer runners, board for bases/side, screws/brackets • Runners to be full-extension soft-close, rated to at least 35–45kg (these are tall drawers) • Mount runners level and square, fit my existing fronts with even gaps/reveals • Attach my two handles Looking for someone with cabinetmaking experience and their own saw — this is a build, not flat-pack assembly. Please confirm you can complete in one visit and that material costs are included in your quote.

Repair wood kitchen drawer

2 worn hardwood runners need replacing inside the carcass of the kitchen cabinet drawers