Find professional kitchen drawer repair in QLD

Looking for a carpenter or cabinetmaker to finish installing two internal pull-out pot drawers behind existing cupboard doors. Work required: - Complete timber spacers—45mm base blocks are already securely installed for one drawer. Add 19mm facing panels using screws only, no glue. - Fit two pairs of Kaboodle 450mm soft-close runners, set back 18–20mm to clear the closed cupboard doors. - Cut the supplied white melamine panel into two drawer fronts, each 445mm high × 540mm wide. - Attach front brackets, fit the pre-made drawer boxes and adjust for smooth operation. Cupboard dimensions: 550mm wide × 550mm deep. Planned 64mm spacers provide clearance around the existing hinges. All materials and hardware supplied. Please bring cabinetry tools, including a fine-tooth or track saw for clean, chip-free melamine cuts.

Quote Needed: Custom Garage Storage and Kitchen Drawers Looking for separate quotes for the two attached garage storage designs, including sliding doors: Design 1: Full-width storage unit Design 2: Shorter, lower-cost alternative If Design 1 is too expensive, we may proceed with Design 2. Please quote materials, labour and installation separately for each design. I would also like another separate quote for four kitchen drawers. Approximate available space: Width: 25 inches Height: 13.5 inches Depth: 21 inches Location: Bellbird Park

Drawers and faces are okay, it's the hardware that connects both that needs replacing/repairing. Hardware is Blum Metabox drawer system, with METABOX front fixing brackets which screw to the back of the drawer face and lock onto the front end of each steel side. On the drawer that’s still together, the bracket has a screw going through the drawer side into it. That looks like the standard screw-fixed type, not Blum’s tool-free CLIP version. So the likely part is: ZSF.1700, sold as a left and right pair. Lincoln Sentry lists it as the screw-on front bracket that fixes to the drawer side with a screw, suiting M, K and H height drawers. If your sides turn out to be the low ones, you need ZSF.1510 instead. It suits N height (54mm) drawers. If they’re the tool-free kind after all, the part is ZSF.1200. It’s the CLIP version of the bracket for M, K and H heights. lincolnsentry To check the height, measure the steel side from the drawer bottom to the top edge. Roughly 54mm is N, 86mm is M, 118mm is K and 150mm is H. Your sides look like M or K, and both take the ZSF.1700. These brackets are cheap, a dollar or two each. Lincoln Sentry stocks all three; take your old plates along and they’ll match them by eye. Not sure which it is, but supplier for Lincoln is in Varsity Lakes Lincoln Sentry 3/481 Scottsdale Drive Job is to replace all these with new fittings in an apartment in Surfers Paradise. There are also 4 other drawers in the kitchen with similar, so depending on price, open to including those as well.

Kitchen drawer slides open after closing, even when empty. Need inspection and repair. Budget includes call-out and labour. Any replacement parts must be approved separately.

Hi, I’m looking for someone to repair two broken kitchen drawers at my home on the Gold Coast. Could you please provide your cheapest price, including the call-out fee and labour? I can send photos of the damaged drawer. Please let me know if replacement parts are extra. I only need the drawer repaired, not the whole kitchen. Thank you.

White 2 pack drawers, 2 lots of 3 drawers below cooktop, need replacing due to damage. It is possible the fronts may be reused/maybe not. Must match remainder of kitchen. Width (across front) of each set 850. Runners (some) also need replacing Preferably as soon as possible

Need kitchen drawer fixed. It doesn’t close properly.

Looking for someone to repair and reattach a kitchen drawer front that has come off the drawer. The drawer front and handle are still intact, but some of the fixing holes have pulled out/damaged the particleboard. Looking for someone to securely repair/reinforce it and reattach the drawer front so the drawer works normally again. Please supply any screws, brackets or small materials required. Photos attached.

Need a few things done 1) Kitchen drawers have come off hinge/perhaps warped with the weight. Need to be re-attached. 2) Ikea TV cabinet doors have come off hinge and not closing properly 3)6 x Door handles have become loose, need to be tightened 4) Ikea walk in wardrobe railing has come off hinge

Looking for someone to repair a kitchen drawer. The drawer slides in, but it won’t stay closed. The mechanism that holds it in place seems to be broken.

Need to replace a door handle and repair kitchen drawers that have slipped off

One kitchen drawer front has come off its fixing. White metal drawer box, Blum Tandembox style. The plastic front fixing bracket has sheared on one side and the broken piece is jamming the mechanism, so the drawer will not release from the runners normally. Job: remove the drawer, take the front off, replace the front fixing brackets both sides (standard Tandembox compatible part, please supply), refit and align. Photos attached. Under an hour for someone who knows kitchen drawers.

Swap out 1 base kitchen cabinet with a pre-assembled 3 drawer cabinet. Install 2 pre-assembled kitchen wall cabinets.

We have recently had an under-sink water filtration system installed, which means the existing drawer behind the cupboard/drawer front can no longer be used. I would like someone with cabinetmaking/joinery experience to: • Remove the existing drawer front from the drawer mechanism. • Refit the existing front so it sits in exactly the same position and maintains the existing gaps/alignment with the cabinetry. • Ideally convert it into a hinged/drop-down solution. • Supply and install the necessary magnets, catches, hinges or other hardware. • Ensure it is secure but can easily be removed/opened when access to the water filtration system is required. The main priority is for it to look exactly as it did previously when closed. Existing drawer front and cabinetry are all in good condition. Photos available. Looking for someone experienced in kitchen cabinetry/joinery who can achieve a neat, professional finish.

I need 8 cupboard doors replaced and 9 drawers ideally something quick as selling my house in Benowa

Have a kitchen drawer wont close. Its soft close Harn system. I think broken. There is opportunity to quote on built in cabinetry required. I will pay what is required. Thank you

I would like a quote to install 5 IKEA drawers into our kitchen cupboard. We have most of the materials (drawers, rails etc). We want it to look something similar to the second photo. The first photo is of the existing space. The third photo is of the drawers we have purchased from IKEA. We are only wanting a quote at this stage, hence the price we have listed. Thank you.

Need Hafele soft close sliding drawer replaced in kitchen

Kitchen drawer. Both sides of soft close mechanism won’t reset back after drawer is pushed in. I have reset springs but after one close it won’t work second time. Runners all smooth. May need 2 new runners as cannot locate hook or latch system. I will just waste more time on it so asking for 2nd opinion ha

The kitchen drawer needs a new sliding bracket as it has broken