Find a trusted window repair service in QLD

Casement window was damaged by tennant. Pried open with screw driver. Dinted timber window and frame Broke hinge mechanism Looking to have it sanded, filled and painted with hinge also repaired.

Have an iveco van that has had some wires cut in an accident, electric windows may need attention and want solar panels and batteries etc hooked up for camper conversion

Need to replace 2 windows to improve airflow into rooms. 2 windows, 1.2m (w) x 1.1m (h) with a hemispherical glass arch atop the 1.1m height (not included in dimensions given). The arch is 30cm in radius. Also, a door is needed with an opening of 1.16m and 2.28m height. I would appreciate a quick response/quote for the two windows and the door at your earliest convenience. Thank you. John Vavra.

old house, needs to be fix on some problems. like door, window, and supporting structure and wall.

Looking for a handyman/carpenter to put proper wood frames around this window and door, as well as fix the plasterboard and install a manhole into the ceiling of our Queenslander.

Fix Window Ledge Broken this afternoon,

I have 2 windows I'd like plaster in. Doesn't matter what it looks like at the back. Also repair powerpoint holes and some minor holes around the house. Will need to be done after my sparky has been. I don't have a date quite yet but assume around the end of July.

Supply and install screen/mesh to two small spaces above a bathroom window in a downstairs garage.

Aluminium hopper window does not fully close to a locking position

Freshly tiled bathroom needs installation of : vanity unit & mirror, single panel shower screen, loo roll holder, towel rails. ALSO reattach architraves in 2 windows.

Broken shutter in my rental that I’m leaving soon. Can take home to repair if helpful. It’s in bad shape

remove old putty, set glass into rebate and replace putty, in situ, on 1st story, you will need a ladder or platform

We want to install fly mesh (as shown in the photos), in 5 windows and 1 door. Mesh will be provided. Note: the door and the windows will need to be taken out to install. I’m putting a couple of photos

There are 3 windows which are sliding down type with spring loaded mechanism. Those do not close fully anymore. Please check photos and let me know if you need more information.

Repair screen door/window mesh.

Hello! 🙂 I would like someone to please replace the fly screen on 2 doors and a small window due to cat damaging them. You would be required to bring the mesh and tools. Suburb is Bracken Ridge (North Brisbane). Measurements are: - Front screen door = 70cm x 195cm (standard size) - Rear screen sliding door = 83cm x 195cm (standard size) - Small Laundry window = 24cm x 81cm. Must be completed before the 16th of May. Please see below availability to have this job completed. Please let me know in your offer if you can make one of these times suite. - Monday 6th between 6pm-8pm - Wednesday 8th between 4.30pm-7pm - Thursday 9th between 8.30am-11am - Friday 10th between 8.30am-10.30am - Monday 13th between 8.30am-1.30pm - Tuesday 14th between 3.30pm-7.30pm - Wednesday 15th between 8.30am-5pm

Remove two metal hoods and install two new metal window hoods from Woodworkers. It's a one piece of metal hood that includes the flashing which needs to be placed under weatherboard walls and then screwed in with the right accessories to ensure longevity. Size: 95cm width Please note that you'll need your bring any necessary tools and joining accessories (screws and etc) as the hoods are being delivered without any accessories. - Please only quote if you have %100 confidence. - Access is easy, ground level. Woodworks generic explanation for install- Colorbond hoods can only be connected by pop rivet joints Metal hoods should clear the external jambs of joinery by approximately 30mm and are usually simply screwed directly to the chamferboards with dome head screws & nylon washers to ensure electrolytic compatibility with the hood metal. Remember water cannot flow over zincalume onto galvanised fixings. Because metal hoods are so light they can easily be installed by two people in a fully assembled state. The metal hood needs to be positioned to avoid interference with the window opening (especially with casements) and ensure pedestrian traffic cannot collide with the hood. Ensuring the hood and window are parallel, the top flange of the hood is usually slipped under the chamferboard or weatherboard overlap and the sides are screwed down with to 4 screws each side. 100) AA •

Wall damage repairs, swap out door bell, pressure wash garage floor, patio, clean outside door, windows, replace a small section in the corner of mouldy grout in the shower

Our lock on our window doesn’t work properly.

I’m needing an aluminium retractable flyscreen fitted to a servery window. The screen is an in mount screen that needs to be cut to size as per the manufacturer’s instructions (provided).