Find a professional mdf contractor in QLD

Finish a kitchen peninsula with VJ paneling from benchtop to floor, not the return. I’ll supply and pre-paint the VJ panels in dark navy blue, understanding I’ll probably have to do some touch up’s post install which is cool. Need the Airtasker to then cut the panels to size and attach including a very slight return to in-fill where the kickboard is on the side view. It’s attaching to semi gloss kitchen cabinets, so ok with glue or small nails (subtle), neat finish. To be clear, the kitchen is already built. It’s attaching cutting and attaching 3x panels to cover the existing cabinet back. The area is about 2.6m long by approx 88cm high. There’s 2x PowerPoints to cut around, one near a corner, the other in the middle. The VJ panels are “surround by laminex” style and I’ve got 3, 90cmx120cm panels to cover the space. They’re 9mm deep. I’ve included pics of what the kitchen looks like, where the panels would go (shaded), as well as inspiration pic and info on the product. Looking to get the task done on Saturday 9 march and will have the air con pumping if it’s hot! Tasker to supply all tools, fixings. Painted panels supplied.

Hello, We’re just wanting to find someone to cut panels of MDF (2400x1200x9mm) into smaller 600x300x9mm panels for us * we already own the panels, happy to come drop them to you, we just need them cut*

I am looking for someone with a table saw that can cut a 3mm thick mdf board into 6cm wide panels. The board is 1800x900mm. This is for a DIY project. Happy to travel for this task. - Due date: Flexible

Instal MDF wall panels on a 4.3 metre bedroom wall. The panels are 1.2 metres wide. - Due date: Flexible

I need some NBN technician to check the connection room in my residential building. The signal internet is not going into my apartment. I contacted the provider and they think that there is some issue in the building connection room. - Due date: Needs to be done on Friday, 28 October 2022

After someone to cut some MDF wood (around 12mm) into the following specs so each end have a wave as per the following image: King | 190cm (W) x 130cm (H) x 10cm (D) Will cover the cost of the wood plus labour. Just need wood cut as per the image - Due date: Flexible

Install MDF Easycraft VJ wall panels on approx 6 walls full height - shadow line ceiling and sit panel on top of skirt so hopefully no removal of skirting board - 3 walls are just "walls" - rest are around door frames so will involve a bit of cutting - Due date: Flexible

I have a piece of MDF timber 16mm thick x 2400mm long x 600mm wide, and I want someone to cut it for me. I need it cut into 5 pieces and it needs to be millimetre perfect. I could use my own jigsaw to do it but it wont be accurate to the millimetre. Tell me what you would use to cut it and your experience. Date can be arranged upon contact but hoping to have it done in the next week. I need the 5 pieces to be as follows: - 38mm x 2050mm - 38mm x 2050mm - 1005mm x 95mm - 1005mm x 95mm - 1005mm x 95mm

I have purchased VJ panels from Bunnings that need to be installed in an en-suite bathroom. The sheets come in 3000mm high and I need cut to 1200mm high and installed onto tiles on a wall. Moulding will need to be applied as well. Job to be done ASAP.

Install easycraft wall panelling on two walls (loungeroom and master bedroom). Need to fit/cut panels to wall size and cut around aircon and power sockets. 9 Panels have already been purchased from bunnings based on measurements. You will need to bring tools (nail gun & circular saw). Loungeroom wall: 230cm H x 443cm W Master wall: 230cm H x 550cm W Date is flexible - I work from home and ideally would like this done within the week

Have the board Have a jigsaw Just need your touch to cut it straight

Installation of VJ Sheet panels over existing plaster wall. 4200 x 2400. (Sheets already onsite) Require removal of skirting, install sheets to spec, re-install skirting then caulking. (Painting not required)

Hello, I need multiple circles cut from large pieces of MDF board (or wood that you would recommend) it’s for an art project and will be various sizes. Work will be ongoing. Must have own tools, (happy to drop wood to you, or can complete at my home) northern GC area. No sanding required.