Find a local Tasker to help you make a kitchen cabinet near you

I’m looking for an experienced cabinet maker or joiner to modernise one corner of my kitchen. I do not want a full kitchen renovation—just a high-quality modification that looks like it was part of the original design. Scope of work • Remove the existing wall-mounted microwave cabinet. • Ensure the adjacent wall cupboard remains securely fixed. • Repair and make good any fixing holes or wall damage caused by removing the cabinet. • Prepare the wall ready for a full-height engineered stone splashback (to be installed later by my stone supplier). • Supply and install concealed supports for two custom floating shelves. • Return after the stone splashback has been installed to fit the two floating shelves (or advise if there’s a better installation method). • Shelves to be approximately 40–50 mm thick in European oak (or similar) and professionally finished. • Ensure the shelves are perfectly level and securely fixed. Quotes Welcome

Need help repairing two kitchen cabinet doors. 1.One cabinet door needs hinge repair — install hinge repair kit on top and bottom hinges, and replace hinges if required. 2.Repair L-shaped cabinet door under kitchen counter — check, repair/replace hinges, and realign door.

Modifying the cabinetry under the sink to create a suitable opening for the dishwasher. I’m not entirely sure about the plumbing, but I’d like to install the dishwasher immediately to the left of the kitchen sink. I’m assuming the existing water supply for the sink can be used to connect the dishwasher. As for the power, there is currently a power point above the kitchen benchtop. However, I would need a power point installed underneath the benchtop, inside the cabinet, which would be approximately 8 inches lower than the existing one.

2 or 4 kitchen doors to be replaced-custom sized, new hinges, before kitchen resurfacing.

Hello, We are looking to do a kitchen reno so will need new kitchen cabinet installed. You will get an empty tiled space to install cabinets that might be sourced form Bunnings or open for suggestion. Will be L shape in on part - with option for Sink, dishwasher and 90m Gas cooktop. and another side to have tall Cabinet with option for Freezer, Electric Oven and Microwave and space for small Coffee counter. Just to give a rough measurement, cabinets will be as : Overall cabinet run: ~7.5 linear metres Main wall: 4253 mm Return wall: 3522 mm Base cabinets: ~10 units Wall cabinets: ~6 units Tall cabinets: 2 units (oven tower + fridge housing) Please let me know esmiate of installation cost. Thanks

Build a cabinet near fridge to match the look

Need a handyman to modify/cut down the overhead cabinet above my gas cooktop so a new rangehood can be installed at the required compliant height. Ideally looking to alter only the single cabinet rather than replace all the overhead cabinets. Then install the range hood I have purchased

I want to install a new dishwasher. Kitchen never had one. Looking at getting a Bosch Series 6 45cm Built-under Dishwasher SPU6IMS01A with the following dimensions 45cm width, 82cm height and 57cm depth. Will need to remove/modify the existing cabinet area shown in picture with blue circle. Bench/cabinet dimensions: 72cm wide, 86cm height and 58.5cm depth. Will also need to make for a path for the dishwashers water/drainage pipes to connect under the kitchen sink.

Remove existing caulking and install scotia trim to base of kitchen cabinetry. Approximately 9 metres around cabinetry. The gap between timber floors and cabinets is anywhere from a few mm to 18mm. See photos attached.

Looking for someone experienced with cabinet repairs/carpentry to realign and get the cupboard door fixed and opening/closing properly again

Kitchen cabinet door hinges needs adjusting. Nothing is broken, just hinge adjustment so the doors can close properly

I'm looking for an experienced cabinetmaker or carpenter to modify two overhead kitchen cupboard doors so they close flush. A replacement rangehood has a stainless steel front fascia that projects slightly further than the original, meaning the two cupboard doors above it now sit approximately 10–15 mm proud when closed. The job would likely involve: Assessing the best solution. Removing the two cupboard doors. Routing/rebating or otherwise modifying the inside edge of the doors to provide clearance for the rangehood fascia. Reinstalling and adjusting the hinges so the doors close neatly and sit flush. The modification should be as discreet as possible, with no visible changes from the front when the doors are closed. Please only respond if you have experience with kitchen cabinetry or cabinetmaking, as I'd like a professional finish. I've attached photos showing the issue.

build 16 IKEA kitchen cabinets.. Carcasses only at this stage. Varying sizes. All boxed and brand new. No internals or doors required at this stage. I am open to paying more for somebody who is experienced with this type of work. It is about the quality of the job, not the length of time it takes to complete. I could be misguided re price here, but i figure a few quotes will give me a better understanding. Please ask any necessary questions

Hi, I require x2 cabinet doors to be made with pre drilled hinge holes. Dimension: 730 x 393 x 18mm Colour: curl birch natural finish. Thanks

Hi 👋 have a standard sized dishwasher I’d like to fit. Previous owner didn’t incorporate a space for a dishwasher… crazy. So require someone to modify cabinet under bench top. Have the cupboard pictured to scuttle - just a collection of bits to be re-distributed. Chasing someone who knows what they’re doing of course! 1) make the necessary cuts and removals 2) do a nice job of it 3) not damage existing counter top 4) dishwasher will be fitted / connected later by a plumber. If this is your gig, and you’re in the area, let me know cheers

I have 4 x IKEA Metod wall cabinets to be installed. They will already be assembled; the job will be to install the suspension rail, and then the cabinets. The walls are brick - masonry anchors might be needed if IKEA’s cabinets don’t arrive with them. Please only quote if you’ve hung cabinets into brick before.

I have 3 small kitchen wall cabinets for hanging. . One of them has a Rangehood (see photos). They are to be installed onto a besser block wall (photo of wall with marking of approximate location) The wall has a tile splash back and the cabinets will overlay the tiles slightly therefore will be a small gap between the wall and the cabinets. Hopefully that makes sense.

4 kitchen cabinet doors needing replacement due to damage. Would like measurement and provision of doors that I can paint and install.

Cabinet Maker Needed to Adjust Kitchen Cabinetry for Stone Benchtop Realignment Looking for an experienced cabinet maker to inspect and adjust existing kitchen cabinetry to allow a stone benchtop to be moved back into its correct position. A stone mason has advised that the cabinetry underneath requires adjustment before the stone can be repositioned. There is currently movement/misalignment in the cabinetry which appears to have contributed to the benchtop shifting and cracking at a join. Scope of Works: Inspect existing kitchen cabinetry and supports. Move and re-level cabinetry as required. Reinforce or adjust cabinet structure to support the stone correctly. Ensure cabinets are level and suitable for the stone mason to reinstall/reposition the benchtop. Advise if any additional cabinet repairs are required.

Hey Guys, I need someone to come and quote for a new set of draws for my kichen. I will remove the old oven and will require ro fill the space with a set of 3 draws 750mm wide. I also need 1 draw 600mm X 240mm. We have a Blum system installed and it looks like a common polyurethane cabnate colour but it would need to be a good match as its next to existing.