Find a local Tasker to help you make a kitchen cabinet in Perth

I am updating my existing kitchen using Bunnings Kaboodle. This is NOT a full kitchen installation and the existing base cabinet are remaining in place. Work required: • Fit new outer/end panels to existing cabinets • Fit new cabinet doors and drawer fronts • Install handles and soft close drawers • Fit new kickboards • Assemble and securely wall mount the new upper/wall cabinets and a microwave cabinet. • Install required filler/pantry/end panels • Remove one remaining old cabinet with a stuck fixing, remove the existing long kick board, one pantry side panel and old bench top. • Trim/install/join the supplied laminate benchtop and cut openings for the sink All Kaboodle components and Bunnings kitchen plans are supplied. Plumbing and Electrical work will be completed separately by licensed trades. I have already removed almost all the old parts of the kitchen except for what was mentioned above.

I have existing wooden kitchen cabinets, and to install a new fridge I need the cabinet above the fridge cavity made a bit smaller, as the new fridge is a little taller than the old one

The screws of hinges have come off which needs fixing. And one kitchen cabinet door does not close property.

2 or 4 kitchen doors to be replaced-custom sized, new hinges, before kitchen resurfacing.

Hi, I recently had my kitchen rangehood die and found out they no longer make my existing type of rangehood anymore. Seems to me, the previous cabinet maker designed the cabinet around the rangehood. By this I mean, they installed the rangehood first and build a spice ledge. I bought a 52cm rangehood (Solt 52cm Undermount Rangehood, Black). However, the new rangehood won't fit due to internal spice ledge in the way. Spice ledge is in up and lower sections. The lower section needs to be removed. Need someone to remove the lower part of the spice ledge and fit the rangehood.

I'm looking for an experienced cabinetmaker or carpenter to modify two overhead kitchen cupboard doors so they close flush. A replacement rangehood has a stainless steel front fascia that projects slightly further than the original, meaning the two cupboard doors above it now sit approximately 10–15 mm proud when closed. The job would likely involve: Assessing the best solution. Removing the two cupboard doors. Routing/rebating or otherwise modifying the inside edge of the doors to provide clearance for the rangehood fascia. Reinstalling and adjusting the hinges so the doors close neatly and sit flush. The modification should be as discreet as possible, with no visible changes from the front when the doors are closed. Please only respond if you have experience with kitchen cabinetry or cabinetmaking, as I'd like a professional finish. I've attached photos showing the issue.

Need to build about 4m of kitchen cabinet to match existing and include a double fridge & double oven.

build 16 IKEA kitchen cabinets.. Carcasses only at this stage. Varying sizes. All boxed and brand new. No internals or doors required at this stage. I am open to paying more for somebody who is experienced with this type of work. It is about the quality of the job, not the length of time it takes to complete. I could be misguided re price here, but i figure a few quotes will give me a better understanding. Please ask any necessary questions

I’ve had an old oven removed from my kitchen and have purchased a dishwasher to go into the same space. The dishwasher does not currently fit because the existing cabinet opening needs to be modified. Dishwasher: Bosch Series 6 free-standing dishwasher, 45cm wide, model SPS6IKI01A Dishwasher dimensions: 845mm high x 450mm wide x 600mm deep It also has a 30mm removable worktop, so height may potentially be reduced to approx. 815mm if appropriate. Current opening is approx: * Width: 580mm * Height: 700mm * Depth: 546mm * Bottom of current opening sits approx. 115mm above the floor I need someone with carpentry/cabinetry experience to prepare the space so the dishwasher can slide in under the existing benchtop. The job may involve removing/modifying the white cabinet framing and raised base/plinth, keeping the existing benchtop in place, ensuring the benchtop remains properly supported, and adding a support panel/leg/bracket if needed. The underside of the cooktop/stove protrudes slightly into the space on one side, so this will also need to be checked as it may affect the dishwasher fit. Ideally, I’d also like filler panels/trim added on either side of the dishwasher so it looks more built-in, depending on what is practical within the budget. I already have a plumber lined up for the plumbing/water connection. This task is only for the cabinetry/carpentry preparation before the plumber attends. Please only make an offer if you have experience with kitchen cabinetry/carpentry modifications and are comfortable working around an existing cooktop. I do not expect any gas/electrical work to be done unless you are licensed. Please include in your offer whether filler panels/trim are included, or whether your offer is just to modify the opening and support the benchtop. Photos of the current space, measurements and dishwasher specs attached.

One corner kitchen cabinet door has come off completely at one hinge so I fully removed it so it needs to be reattached. I doo not know if the hinges need to be replaced. The other does not close properly I think because there are two different types of hinges on it. I need it to close properly so may also need new hinges.

Need someone to make me a new door an cover gap above draw

Make a door and make the old draw be able to sit back in

Make room and remodel cupboard doors for a Fisher and Paykel series 7 dishdrawer (to be installed by a plumber). The dishdrawer is to go in the bottom-half of the cupboard. The cupboard doors are to open the same way above the dishdrawer. The sink is to the right of the photo. Let me know if you need additional info or photos.

Cabinets hinges needs adjustment and tightening Someone who knows what they are doing Please quote ypur hourly rate Riverton

I need overhead cabinets for the kitchen

Modify over fridge cabinet to accommodate taller fridge. - View all the details of this offer: https://www.airtasker.com/offers/01KE5VDFAV4RA28HT6T77Y59DQ

Re-work /reconfigure /shift some existing kitchen cabinets and bench tops. Shift cook top, oven and HWS. Instal pantry. Create bigger fridge space

To install kitchen cabinet door - View all the details of this offer: https://www.airtasker.com/offers/01K2EYMW0VJ7R56QV2JSP4WJRC

Paint laminate kitchen cabinet doors and drawers Prep and paint laminate kitchen cupboards and drawers (original colour is cream, and will be painting them white). Only the outside of the cabinets needs painting, not the inside shelves. - 13 cupboards (double doors). - 4 drawers - Surrounding areas (laminate around oven etc) Paint and materials required will be paid for!

quote to repaint my small-ish kitchen, mostly old (1990s) flat surface cabinets as per photo attached, plus new ikea (flat low gloss surface “vallstena”) 220x60cm pantry (will be stand-alone on wall, so 3 sides) and adjoining 60x60cm ikea 3 drawer-base cabinets (3 sides each as will be an island bench). quote to include priming, sanding etc