Find an experienced cabinet maker near you

Looking for an experienced cabinet maker or carpenter to replace water-damaged internal cabinet boxes (carcasses) under a double kitchen sink. The exterior doors, handles, benchtop, and surrounding cabinets are intact and will be reused. Measurements: Width including the carcass as shown in photos is about 997–1000 mm. Height as measured in the photo is about 727–730 mm. Depth as measured in the photo is 557–560 mm. Scope of Work: Measure & Fabricate: Supply and build new internal cabinet carcasses using High Moisture Resistant (HMR) board/melamine to fit the existing space. Open back cabinets are acceptable. Removal: Safely remove damaged particleboard sections (under-sink floor, damaged middle shelf, lower drawer box area, and center support mullion) without disturbing the benchtop or sink. Installation: Fit the new HMR cabinet box/shelving, including neat cutouts for existing plumbing pipes (drainage pipe and water inlet lines). Reattach: Re-hang existing white cabinet doors, align hinges, and re-fit the bottom drawer runner/front. Damage Details (See Photos): Water damage from a previous leak has caused the particleboard base, middle shelf, and center support post to swell, split, and crumble. 3 internal lower sections and 1 bottom left drawer space need rebuild/re-boxing.

Inspection Only - need a cabinet maker to replace skirting after dishwasher installation. Work must be professional.

Hello, need a cabinet maker to build / install a cabinet in a wardrobe and a cabinet in a living room.

Im a carpenter builder. The client has cabinets she needs installing. She’s chosen ikea for the bedroom. We’ve built the carcasses (need to cut down and install 16mm melamine sheeting to the back) and install in the bedroom. Wanting a per hour rate as there are alterations required. Few days work.

I need an experienced handyman or cabinet maker to pack out either side of this cabinet & install the runners so the drawer can be used in this cabinet opening. The drawer & fascia fit the opening perfectly & it's just setting the runners up at the correct width & height is the challenge. The job is Jan Juc.

As per photos written quote required from qualified carpenter for the work as mentioned in photos for Insurance

Hello, I'm looking for someone with experience in cabinetry, built-in wardrobes or joinery to finish an IKEA PAX wardrobe install to make it appear built in and a tidy finish. Scope of works 1. Install infill/filler panels • Fill the gaps between the wardrobe and the side walls with 16mm MR MDF. • Scribe the panels to the walls where required so everything sits flush. • Ideally use moisture-resistant MDF or similar ready for painting. 2. Install a kicker/plinth board • Cover the existing timber base with a neat kicker/plinth with either 16 or 18mm with 16mm MR MDF. • Continue the plinth across the full width so it appears built in. • Minimise visible joins. 3. Finishing • Light sand and prime final cut and fitted pieces • Colour match GRIMO door at Dulux trade centre • Ideally, paint with low sheen Dulux Aquanamel and using high-density foam roller to achieve sprayed-looking texture • Finish neatly against the existing skirting boards and also IKEA base (may require some filling of gaps above plinth / kicker) • Caulk as required. Notes • Wardrobe is already fully assembled and secured. • Photos attached showing the areas to finish. Please only apply if you've completed similar built-in wardrobe or cabinetry work. Photos of previous jobs would be appreciated. Cheers,

I have 2 wardrobe recesses. 1 master and 1 small recess. For now I just need a hanging shelf in both. White 20ml thick shelf? with pine wood supports underneath and a heavy duty silver pole. I will pay for materials extra. Other work available 😊

Looking for a skilled cabinet maker, carpenter, or handyman to build and install a custom floor-to-ceiling storage cabinet/pantry in my apartment, based on the attached sketch. The cabinet will be positioned around an existing structural column/wall and should maximise storage while maintaining a clean, modern look. Please provide your offer.

Cabinet Maker Needed to Adjust Kitchen Cabinetry for Stone Benchtop Realignment Looking for an experienced cabinet maker to inspect and adjust existing kitchen cabinetry to allow a stone benchtop to be moved back into its correct position. A stone mason has advised that the cabinetry underneath requires adjustment before the stone can be repositioned. There is currently movement/misalignment in the cabinetry which appears to have contributed to the benchtop shifting and cracking at a join. Scope of Works: Inspect existing kitchen cabinetry and supports. Move and re-level cabinetry as required. Reinforce or adjust cabinet structure to support the stone correctly. Ensure cabinets are level and suitable for the stone mason to reinstall/reposition the benchtop. Advise if any additional cabinet repairs are required.

Looking for a cabinet maker to turn two wardrobes with two doors into sliding doors with mirrors & shelving and draws like my inspiration picture attached. All materials will need to be provided by you so please quote including the doors etc Also would like some shelving and draws in there as well. Will attach an image of what we are liking the look of. Approximately 2mtrs wide.

I need a cabinet-maker to build 2 custom wardrobes in my apartment. I want the same design as the ikea ones but custom sizes. Happy to discuss price if needed

I am looking for someone to go around after the cabinet maker to make all the cupboard doors straight. They all need adjustments

My bottom two drawers have come of their rails, one is completely out and the other doesn’t slide.

Hi there I am working on a new clients home and need some cabinetry made and installed. Please include photos of work you have completed in your offers or comments. Thank you

Cut out a space for a dishwasher under bench in an existing kitchen cabinet. Still need to maintain the appearance of the kitchen. I want to be able to have the remaining cupboard space under the sink as well so a small door or a blank can be installed between the edge of the dishwasher and the next door. Pillar will need to be moved across. I have some photos with the measurements. Dishwasher is 820mm high, 600mm wide and 570 deep. Parking is off street (I have a driveway)