Find an experienced plumber in Heidelberg

Plumber sought for RAM cross handle pillar taps to be installed in bathroom sink plus removal of current taps

Installation of bidet spray and replacement of shower bottom seal

Remove laundry taps. Cut existing pipes shorter. Permanently seal pipes so can be concealed in wall cavity. I will patch the plasterboard. I will dispose of waste materials. I will clean up. Must be licensed and provide warranty for work. See photos with approx measurements. Must be able to do the job so that the hole does not effect the existing bench top and can be covered by new splash back (height shown in photo).

Need someone to fix suspected Under-Floor Plumbing Leak- constant wet patch on carpet in bedroom opposite corner to the ensuite) that doesn’t clear up. Soaks through a towel in 24 hours. House is on a raised foundation/ stumps so assume it’s coming through the floorboards

House built in 1994. Bath tub upstairs. Seperate handle and same spout. Hot water not working. Have tried to replace spindle although not exactly the same. Does not seem to be damaged anyway. When I’ve had it off and turned mains back on there is the slightly amount of water coming out of the hot side. When I turn the cold water on it comes out of the spout and out of the hot side opening. Additionally some older style taps are leaking

I am seeking a VBA-licensed plumber with drainage experience to provide an independent assessment of a bathroom renovation in Heidelberg, Victoria. Background During demolition, it was discovered that the existing shower waste exits through the wall rather than the slab and sits approximately 80mm above slab level. The current contractor has advised that a standard low-profile shower hob is not achievable and has proposed a significantly higher shower hob and raised floor. I need an independent assessment to answer: Is it possible to achieve a compliant low-profile shower hob (approximately 15–50mm) with the existing drainage configuration? If not, what alternative drainage or construction solutions are available to minimise the shower hob height? Is the proposed high hob and raised floor a reasonable solution? Is the specified compressed flooring sheet suitable for covering the former bath opening, or would another solution be preferable? Scope Inspect existing drainage and waste configuration. Assess shower hob and floor level options. Identify alternative drainage solutions. Consider risks associated with slab or wall modifications (apartment with a unit below). Provide a detailed written report with recommendations. Requirements ✔ VBA plumbing licence ✔ Drainage experience ✔ Public liability insurance ✔ Ability to provide a written report Please include your licence details, relevant experience, availability, and fee for inspection and report.

I need a sink overflow installed to my laundry sink. Existing sink does not have an overflow, however S trap does has provision for overflow to be installed. Works include the supply of a suitable overflow kit that ensures water tightness.

Access the under floor space to turn off faulty water pump. Easy to get to with 1.5 metre height of area beneath house

I would like a new tap to be installed behind a fridge, with a pressure regulator and shut off valve. Once this is done I would like the fridge to be connected to tap. There is easy access to water right out side.

We have replaced the sink in our vanity and the waste outlet no longer lines up correctly with the pipes. We have the new vanity waste ready.

Hi. I have a leaking bathroom sink where water is dripping into the cabinet below.

Need taps and laundry unit put in

Kitchen tap adjustment/replacement - if you let me know what type of tap, I can purchase prior to the job. Not sure if a mixer tap can work or needs the same set up. Thank you.

Need some taps connected to the bathroom and kitchen the taps are already supplied

Water is leaking from the bottom of the toilet when it is flushed. Needs the rubber seal replaced.

Small shower (approximately 1m²) requires old caulk/silicone to be removed and replaced with mould-resistant bathroom silicone, ensuring a clean, neat and watertight finish. Additionally, we would like someone to inspect the seal around our bathroom sink drain, as there appears to be some mould/grime buildup, and advise whether resealing is required. Preferably looking for someone with plumbing experience or a licensed plumber, as we may have additional plumbing work in the future.

Water pressure in shower is very low

My tap in the bathroom basin is loose , it was fixed previously about a few moths ago but a now loose again. Very frustrating .

Chipped sink from dropping something still got the piece that came off, doesn’t need to be ‘perfect’, I know it will still be visible after repair most likely, but eye for detail kind of person with experience would be great.

Need to reconnect this tap.