Find professional kitchen drawer repair near you

We need a new laminated board cut and installed to fit new smaller wall-oven where the existing wall-oven is. There will be room for another drawer to be made to match existing drawers, and installed underneath. Need quotes to have any idea of cost, which is why we have just put $300 in the field required to post this job online.

I have a damaged drawer front (cracked surface). I'm looking for the most cost-effective way to fix it before selling: Can it be re-wrapped/resurfaced with white gloss vinyl? If not, please quote to replace only the front panel of this drawer.(925mm*240mm) If a match is impossible, quote for replacing all 9 drawer fronts(6 are 925mm*240mm*20mm and 3 are 925mm*150mm*20mm).

Drawer water damaged, most can ve reused includibg frobt panel and rillers

Have two sliding kitchen drawers on a soft close mechanism that won’t close properly.They are constantly slightly ajar Likely to require replacement runners or whole new draws maintaining the same draw front if possible 2) some acrylic cabinet covering that needs to be re glued on three cabinets to smarten it up aesthetically 3) gas fob lighting unevenly 4) waterproof sealant between wall & vanity unit in bathroom

The front of a kitchen drawer keeps sliding out. It's either the mechanism or the drawer itself but i am unsure which.

I have some sliding drawers that have broken attachments (to their slides) and a couple of cupboard doors that also have broken or missing spring attachments. I am not sure what these things cost, so budget is a guess.

Install a baby gate across a kitchen entry point and another one outside which requires drilling into a wall. I also need a kitchen drawer fixed back on.

Just need to repair the kitchen drawer. Not missing any screws, and runners work fine

Need a fix for my 3 kitchen drawers. They are bit misaligned and loose. I tried to apply a fix but that did not help. 1 photo is with the fix that I applied & the other photo is a good part. Any materials will be paid seperately

My kitchen door seems to have sprung out in the middle. I suspect that’s a very simple fix but it might require dismantling the drawer and putting the front back on

Kitchen drawer track has broken. Need it reattached to the kitchen cabinetry. Also need to install a new door handle to a bedroom door.

The current gap open at 410mm so I can not upgrade the drawer slide to soft closing due to I need to narrow the drawer to allow thicker tracking system. Can you build new kitchen drawer to be narrower, re-use drawer face and install soft closing track. You can quote to do one drawer. If works, I have another 7 x drawer for you. Given: Cabinet internal opening: 410 mm 
Drawer slides from Bunnings warehouse Goliath Soft Close Drawer Slide Pair - 450mm is 45 mm per side. Total space taken by slides = 45 × 2 = 90 mm Drawer outer width required = 410 − 90 = 320 mm So the drawer box should be 320 mm wide (external width). Practical note: 
Most installers will reduce this by another 2–3 mm total for smooth operation, so a real‑world target is often around 317–318 mm. The answer was provided by me but I need comment from experienced installer as I never build a drawer myself before . Also if you choose different brand of the drawer slide the width will be different as well.

The front of my bottom drawer in my kitchen has come apart and I need it repaired

The front facia has come away from a Blum kitchen drawer. It looks as though the screws have pulled out of the facia. The drawer looks to require disassembly to fix this. After someone who is familiar with this type of drawer system. I also have others that need to be realigned too if possible. Not sure if the cost to fix it. Happy to discuss if it’s a bigger job than it looks.

Kitchen drawers need to be made to fit this space. 4x drawers required. Have tried to source with various suppliers but the drawers are so old that a whole new set to fit the space needs to be built. Do not have measurements. Will need a measurement done and then drawers built and then return to site to install drawers, unless it can be done onsite.

It's not a big job, maybe the locks need to reassemble who holds the drawers.

Reinstall a kitchen drawer.

My kitchen drawers are push to open, spring loaded. There are 3 altogether and the lesser used drawer is OK. However the 2 frequently used drawers are becoming hard to open. Rather than a gentle push you actually need to hit really hard to make them open. Added to that one side of the larger drawer often doesn't catch properly so it sits lopsided. Its getting pretty annoying as you virtually have to smash the knife and fork drawer really hard with your fist to open it. They are branded KROME fittings (see image). I would like either to adjust or fix the current fittings OR replace with some other type of fitting that works. Naturally will pay for materials used. It is not an urgent job but would like to get it sorted over the next few weeks. Not sure what to put as cost as have no idea the time it would take so feel free to quote and explain. Cheers Cathy.

The shower head won't stay upright. Keeps tilting forward and back. Finding it difficult to tighten it. Kitchen drawer seems to be stuck and can't pull it out.

Own tools needed! 1. We have a kitchen drawer and soft close rails are broken. Old one to be removed and new ones put on. We have the kit from bunnings but require a drill. 2. Put the mount for ring camera outside. Will need a drill. We can provide ladder