Find an experienced handyman in South East Melbourne

Needing 1x blind replaced

Need help to change a new sink and water tap for kitchen. We can buy the materials. Need a handyman help

I have a set of fleximount shelving that needs to be installed inside the garage. The garage walls are brick. The mounts need to be drilled into brick and not the mortar. Ive given up trying to get the holes to line up straight. There are approx 48 holes to drill.

Hi guys, I need your help (either handyman or tiler) to fix a small tile section and patch 3 holes on wall (2 big one are 10cm wide) and 2 small holes (due to old screws, just remove it). House is in Clarinda, which 3’ drive from my house in Oakleigh South. The bottom section/row of tiles (left, right and centre) on the door steps are falling off and unstable as previous tiler didn’t do it properly. Need to glue it back again properly and regrout that small section and fix tiny crack. The old tiles behind new tiles are the old glossy tiles (please see the photo attached of old glossy tiles). Please use weatherproof/waterproof grout and adhesive. This job is Oakleigh South. Please let me know if you can do it. Thank you, Steve

Repair hole in drywall/plaster wall and repaint to match existing wall colour.

Replace a ceiling fan with light. New fan supplied

Garage ceiling plasterboard has collapsed. Roof as seen in picture, 3mX2.5m approximately. Looking to put new plasterboard and any sanding. No need to paint as this Will be done separately.

I have an already cracked pane of glass that I would like removed and a dog door installed with wood patching the remaining gap.

I have a large hole in the cornice after removing a wall heater removal, that needs plastering

Looking for someone experienced and careful to install a brush cable entry plate on the side panel of my wall-mounted network rack cabinet. Please see attached photos for reference: * Red mark indicates approximate installation location * Brush plate photo attached as well Scope of work: * Carefully measure and cut opening on the side panel of the rack cabinet * Install the supplied brush plate neatly and securely * Provide screws/fixings required for installation * Cabinet must remain mounted on wall (do not remove cabinet) Important: * Need clean and tidy workmanship * Must avoid damaging: * existing cables * cabinet structure * surrounding wall/cabinet finish * Prefer someone experienced with network racks, AV, cabinetry, or metal cut-outs Tools required: * Suitable cutting tools for metal cabinet panel * Vacuum/cleanup after cutting preferred Location: Berwick Need to be done today

I am after someone to help install a garden shed - Abasco 3 x 2.26 x 2. Slab already in place. Friday 8 anytime of Sat 9 in the morning

Need this small mirror to be hanged to wall in the hallway

I’m looking for someone to fix my letterbox that got damaged, I can provide the new letterbox, I just need someone to fit it for me. The floor concrete is solid from the previous letterbox no damage to the concrete

I need to get a cat door put into my front door (timber). I’ve attached photos of the door as well. Please give me a quote. It needs to look neat for body corp. If possible needs to be done Monday night or sometime during the day on Tuesday.

Have already taken out the passage door lever. Will need assistance to drill new holes to fit the slightly larger entrance door lever set

Need to supply materials and complete jobs: - Front door handle need tightening - Front door needs paint patch where the markings are - Back gate needs proper latch installed - Kitchen sink and edges need re siliconing - Bathroom sink need re siliconing - X4 toilet roll holders to be installed. (1 would be to tiles and the rest into plaster)

We’re looking for someone handy to help restore our window frames after we’ve recently removed screws from them. Around 8 windows in total The job involves: Sanding the window frames to create a smooth surface Filling the screw holes neatly Repainting the frames for a clean, finished look We’ve attached photos for reference so you can see the current condition of the frames.

The base of the garage door has needs to be screwed. I think I will need 3-4 screws to hold it into the door.

I’m looking to have a pet door installed through both a wooden door and a security door. I also need a simple gate setup on the sides to keep the area enclosed. As the property will be demolished in the future, I’m after a solution that’s cost effective but still durable.

Fix this hole, looking for quotes