Find experienced local carpenters in Sydney

Wanted: Stainless Steel Flue Pipe & Fittings for Pool Heater Required Items: Flue Pipes (125mm / 5-inch diameter): 3x 4-meter lengths 1x 2-meter length Fittings (to match 125mm / 5-inch flue): 90° elbows (specify quantity needed) 45° bends (specify quantity needed) Material & Construction Requirements: Material: Stainless steel corrosion resistant Seams: Must have welded seams (required for gas heater installation safety). Prefer the above lengths, but if you have another configuration please advise.

I need a carpenter or handyman to assess and fix a wall-mounted Murphy-style fold-down table that has been sloping past horizontal since installation. The gas strut is concealed inside the mechanism, and its mounting position may be incorrect. I’m looking for someone who can diagnose the issue and recommend a practical solution, such as adjusting the strut position or installing a suitable cabinet stay or mechanical stop to keep the tabletop level at 90°. I do not have the necessary additional gas struts or cabinet stays at hand. It may have to be purchased separately. Experience with hinges, gas struts, cabinet stays, furniture mechanisms would be helpful.

I need a carpenter or handyman to assess and fix a wall-mounted Murphy-style fold-down table that has been sloping past horizontal since installation. The gas strut is concealed inside the mechanism, and its mounting position may be incorrect. I’m looking for someone who can diagnose the issue and recommend a practical solution, such as adjusting the strut position or installing a suitable cabinet stay or mechanical stop to keep the tabletop level at 90°. Open to all ideas. I do not have additional gas struts or cabinet stays at hand. Experience with hinges, gas struts and custom furniture mechanisms would be helpful.

We need a skilled carpenter to create the joinery design for our up and coming bakery in Marickville. We would also require their assistance in installing a few wall hangings.

I’m looking for a solution-driven carpenter or handyman to assess and fix my wall-mounted fold-down table. The problem The table folds down from the wall into a horizontal position. It is currently usable, but the gas strut appears to push the table a few degrees beyond the desired 90° horizontal position. As a result, the tabletop isn’t perfectly level, pencils can roll off, not a deal breaker but annoying. I’d like someone to assess whether adjusting the strut’s mounting position or the mechanism itself could correct this. I’m open to practical solutions, including: * Repositioning the gas strut mounting point to improve its angle and leverage. * Recommending and installing an appropriate mechanical stop or additional support if needed. I’d prefer to retain the existing table, rather than replace the entire mechanism. Important details * This is a wall-mounted fold-down table: it opens by folding down from the wall, not by folding up. * The table is used daily, so the solution needs to be safe, stable and durable. * I’m looking for someone who can assess the mechanism and recommend the best solution. Experience with gas struts, hinges and custom furniture mechanisms would be ideal.

Rebooking task between David and Aaron

Looking for an experienced handyman or carpenter to add thin decorative shaker-style trim to my existing glossy white kitchen cabinet doors. Scope of work: * Add very thin rectangular trim (approximately 6–8 mm wide) to the upper kitchen cabinet doors only. * Measure and cut trim with neat 45° corners. * Attach trim securely and finish all joints. * Prepare and paint to match the existing glossy white cabinets. * Install small brass knobs on the upper cabinets and brass handles on the drawers. * Keep all existing cabinet doors, layout and finishes unchanged. I can provide inspiration photos and photos of the existing kitchen. Looking for a clean, professional finish. Please quote including labour and materials. The left photo is the before and the right in the inspiration for reference.

Someone with woodworking experience/confidence Hi there! We have a mid century Danish tallboy that has wooden runners. The drawers no longer sit on the runner properly, due to the runners wearing down over time as well as the grooves on the drawers themselves. We would love to have these fixed/replaced so that the drawers can be opened and closed freely. There are 6 drawers total

Approx 2.5x2.5m bathroom ceiling to be cleaned, primed and painted. New stair balustrade to be stained and polyurethaned. All paint will be provided.

Our shoe cabinet door has become dislodged due to a damaged screw where it is unable to connect with the rest of the cupboard. It has made the door unstable and we cannot use this part of the cabinet.

MUST BE COMPLETED TOMORROW. Looking for an experienced, insured carpenter to supply and install structural timber backing for 3 floating shelves. Shelf installation will be done separately. SCOPE OF WORK Supply 6 timber noggins (structural-grade timber or LVL): - 4x 570mm long x 70mm deep x 120mm high - 2x 420mm long x 70mm deep x 120mm high Final lengths to be confirmed on site. Install all 6 noggins securely between existing timber wall studs, flush with stud faces, using suitable structural fixings to resist twisting and shelf loads. Cut and remove plasterboard to access studs for 2 noggins. The other 4 are already accessible. Electrical wiring is present, so care is essential. NOT REQUIRED: Plasterboard reinstatement, plastering, painting, tiling or shelf installation. REQUIREMENTS - Available tomorrow, Friday 16 October - Current public liability insurance - Quote includes all materials, fixings, labour and cleanup Photos of existing wall and proposed layout attached.

Hang 2 small stainless steel shelves, and unscrew picture screws in living room

Looking for an experienced carpenter, joiner, or heritage window specialist to repair the damaged internal timber rail/glazing bar on a timber sash window. Either splice in replacement timber / use an epoxy wood-hardening and filler system or replace the damaged section cleanly, sand flush, and prime/paint to match the existing white finish.

I need a small section cut out of a kitchen cabinet shelf to fit my new refrigerator into place, in Pyrmont . The cabinet is above the fridge and only half depth, so only the front portion of the shelf needs a notch cut. The cutout needs to be roughly six inches by six inches to clear a raised cap on top of the fridge. This should be a short job for someone experienced with carpentry or cabinetry who has their own tools. Ideally completed this coming weekend. Budget around 80 to 150 dollars, happy to discuss based on your quote.

Cut down joinery 100mm on the left. Must have proper equipment and experience

Carpentry. Replace a 100mm dia. Pine log pergola beam that has rotted and split in half. The pine log is approx. 3.5m long and notched at each end and fixed to supports. We will place this inside of the polycarbonate roof so the beam doesn’t rot out again.

Install cabinet doors Doors are Kaboodle from Bunnings, hinges are provided. 2 x doors are 2005mm high x 637mm width The door frame is 1282mm wide x 2022mm The doors are made to measure for a pantry style laundry. Bunnings order is pictured for reference

Cabinet door hinge has come away due to the holes too big for the screws. Door and hinge are fine, just need reinforcement within the holes. I don’t have the tools or parts, so looking for someone who can bring the necessary equipment to reinforce the door onto the cabinetry. Please include any additional payment required for parts.

Hi we need a carpenter today to: - make a coffee bar benchtop slightly bigger - remove 1 post to fit a drinks fridge underneath the coffee station

IKEA cabinet is too tall for space and we need to cut 5mm off. Circular saw required will need to bring with you