Find a local Tasker to make you custom furniture near you

Experienced cabinetmaker wanted to install wardrobe and 4 cupboards. Units already assembled. Going into space prepared by builder.

I need a joiner to install a kitchen & laundry cabinets. Picture attached is the kitchen & bathroom combined room that is about 12sqm I need a joiner to measure up and sketch and make the cabinets. I will pay for all material.

Experienced cabinet maker required to install magic corner pullout kitchen drawer into an existing blind corner cabinet.

Need a cabinet maker make some overhead cupboards and broom cupboard with built in desk as pic.. wall is 2850mm wide and 2700mm high

Laundry and vanity installation and some carpentery job wall and door installation.

Need a small office kitchen fitted with cabinets, bench top and splashback

Require a kitchen cabinet maker to assist with cupboard above our fridge area, fridge slight too high so it wont fit in the area as required - unsure if existing can be slightly cut down to allow it to fit or maybe bottom shelf removed and doors filed down image attached your quote would be appreciated thanks

Alter kitchen cabinet & remove draw assembly to fit bar fridge under bench & finish off base board

Need a u-shaped kitchen for a new room in a renovation; ready to go. Need ASAP

I need a cabinet maker to attach timber handles to wardrobe please. 6 X drawers 3 X doors See attached pics. Also need one picture put on a solid wall please. Thanks!

I need a laminated panel cut to size and two holes cut out for fitting in an oven and microwave

Drawers built in along the wall pictured. 302 cm wide (to the skirting board) Approx 45 cm deep Approx 90 cm high 3 sections with 3 drawers deep (9 draws total) Timber top on it, with white front. Sample 2 pics provided to get the idea.

Place a door on exiting cabinetry to create a linen closet with an additional shelving unit. Form ply provided. Picture below door where the wine rack is currently and is to open upward. Plans and measurements below.

2 x pull out drawers need their fronts fixed back on. Picture shows 1 of 2 that are exactly the same, except they are both right off now. You will need some dowell and cabinet fixings I would imagine. We have guests for dinner arriving at 6pm so must be done and dusted by then. I can't do it myself because I am committed to other projects already until 5.30pm.

I’m seeking to remove a kitchen cabinet so we can install a dishwasher. Need the cabinetry removed (I think some cabinetry like bottom panel will need cutting) and need a hole cut in the side of the remaining cabinetry for the dishwasher cables to go through to the next cabinet over under the sink. I have measured and it appears that removing the cabinet will leave the 60cm required for dishwasher. It would be great if cabinetry could also be taken away after job.

Task 1 Remove inserted grids and replace with two doors with a shelf inside each to act as a linen cupboard. Formply for doors supplied. Cupboard hinges required. Internals of grids can be repurposed to shelves. Task 2 build a desk into an existing wardobe to increase function

Looking for a skilled and experienced carpenter/cabinet maker to provide a quote to supply and install: 1. wardrobe inserts in bed room, 2. sliding doors in garage, 2400Hx3600W 3. new hinged door for lounge.

Hi We are looking for someone to work with us to plan out a cabinet solution fit for the space in the attached photos, due to limited space we are looking for a smart system that allows us storage, adjustable/flap in and out bench top and overhead storage. We’re not 100% sure on the best way forward so we need someone experienced to work with us to find and implement the right solution. The budget is just for the assigning, planning and quoting.

Approx 2 hours work. Will need own tools. Panels need to be cut onsite

There are 3 book cases which needs adjustments from the base as it is not sitting flush with the wall partition. See pictures below. Assistance is needed with adjusting slant on adjoining bookcases and adjusting slant on another so it is not leaning forward. Will also need assistance with working out how to affix the bookcases to partitions so it is not leaning forward.