Find experienced local carpenters in Inner West Sydney

Need garden shed assembled . Dimensions are 3.45m x 1.86m x 2.02 m. It will be placed on an existing concrete slab

1. Dismantle our old shed 2.25x1.5m. Stack the pieces neatly against the wall. 2. Build our new shed 2.25x2.25m. New shed is EasyShed brand and comes with concrete fittings. Located in basement car space. Please send me a quote :)

After installing a new dishwasher we need to have the kickboard trimmed to fit

Supply and install 6 shelves between wall Please see sketch for sizes and thickness of shelves

Need to get the height of this table partition reduced, it has metal frame and board (photo below). After cutting/slicing we need to place the topcap back so it looks good. Thank you.

I am looking for a licensed professional carpenter/engineer to provide detailed design drawings for a free-standing platform for an indoor "tree-house" to stand on the stairs in the stairwell to our apartment. I can provide the measurements on request (or welcome to visit and take them personally if preferred; roughly, the platform shouldbe 1.3m × 1.3m width and length, the shorter side 2.2m hight, and the taller side 2.8m). Attached are photos of the stairwell as well as a rough sketch of the base (with some beam at the forefront not shown so that the background can be seen), and maybe some beams on the diagonal to be added too. The taller end will be at the bottom of the stairs, with the platform floor sitting tightly between the three walls.

Need assistance for disassemble my kitchen cabinet so that my old dishwasher can be removed. Once the new dishwasher is installed, need to re-assemble the cabinet and apply silicone at the bottom.

One heavy cabinet to be installed in the kitchen 1500x1200x450 I’m here I need someone to help me Wednesday morning

Installation of 3 x Internal Hollow core doors (2040 x 770) including attachment of hardware (Hinges / Stopper / Lever Set) to existing door frames. One old door is still attached and will need to be removed. (Other two doors have already been removed) Painting of new doors and disposal of old doors not required. Prefer qualified carpenter as more complex tasks to follow to quote.

I’m looking for someone with the right tools to cut away a large rectangle from the back board of my kitchen cabinets. I’m inspecting the area for signs of mould. You’ll need to make sure your hand tool fits in the cupboard space and that you don’t damage the back wall.

Need a handyman/carpenter to install 6 shelving displays units, please see photo below. They are replacing existing ones that have been removed as seen in the photo with the blue circles. The new units to drilled into gyprock walls. Need own tools. Panels are 1200×1200 weigh about 20kg each

Handyman assistance required on a boat in a marina in Balmain area. Some experience with electronics and electrics a bonus. You must not be the seasick type.

Build a flat pack swing and mount it to porch

We want to put in a dishwasher (Bosch Seires 2 SMS24AI01A) and need to retrofit the kitchen. Task: - Remove drawers and cut out bottom silver kick panel (also wood I believe) to fit dishwasher. Space measures 89 W x 85.5 H in cm (bench bottom to floor), though may be able to get a little extra height as the floor doesn't extend under the cupboards. Dishwasher is 60 W x 84.5 H - Create stable platform for the dishwasher to sit on if needed and cut any required holes for plumber/electrician to use. - Cover the new gap in frontal area with old material as the dishwasher is quite a bit narrower than the drawers.

Need a welder to repair four small holes in stainless steel wet area

I need someone to remove 2 skirting boards and cut a corner of the skirting board to fit a fridge

We need a Carpenter to go into a cupboard and cut away some of the cabinet to provide access to the plumbing behind it.

I require someone to assemble a brand new garden shed. The surface is a reasonably flat paved driveway with easy street access. Product: Absco Shed 3.00m x 0.78m x 1.95m Monument Ezislider Double Sliding Door Garden Shed

Hi we've picked our kitchen and laundry bench stone and decided a colour scheme (polytec). We need this and built in cupboards drawn up including elevations.

Carpenter needed to plane table legs by 200mm