Find experienced local carpenters in Castle Hill NSW

I am looking for a single replacement cabinet door for my kitchen. Specifications: Width: 600mm Height: 690mm Thickness: 16mm Style: Flat panel (no profile) Finish: High gloss white Quantity: 1 The door will be used to replace an existing kitchen cabinet door above a rangehood. The kitchen was installed by the developer Mirvac around 2010, and I would like the new door to match the existing colour and finish as closely as possible. I can provide photos and measurements of the existing door, and I can also bring the existing cabinet door to you if required for colour and finish matching. Could you please provide: A quotation for supply only. Lead time for manufacture. Whether you can colour match an existing door sample. Whether the door will be supplied with edging/sealed edges suitable for a kitchen environment. Whether hinge holes can be pre-drilled to match the existing door (if I provide the measurements).

Hi there, I have recently settled into my new home and found that the existing refrigerator cavity is 180 cm high, while my refrigerator is 190 cm high. To accommodate my fridge, I have removed the over-refrigerator cabinet myself. I would like to have this cabinet professionally modified to reduce its height by 13 cm. Please note that I will handle the reinstallation myself. I can drop off the cabinet at your workshop and pick it up myself once the modification is complete, so I only require the workshop modification service. I have attached a few photos for your reference, including one labeled "picture 4" where I have marked the panels. I would appreciate it if you could assist me with the following questions: 1.What would be the estimated total cost for the cutting, painting/refinishing, and overall modification? 2.What is your current turnaround time for a job like this? 3.Can the existing hinges still be reused? When modifying the cabinet, would you be able to pre-drill the new hinge holes (concealed hinge cups) for me? 4.Please refer to the attached photo "picture 4." I have labeled the panels from 1 to 5. My understanding is that all 5 of these panels (the back panel, two side panels, and the two doors) will need to be trimmed down vertically to reduce the total height. Is my understanding correct? Thank you for your time, and I look forward to your quote and advice. Best regards, Xiang LIU

Have a kitchen bench top that has cracked. Need to have it replaced with a new cooktop and oven

I like to install below cabinet in my house wardrobe with mirror: 2300*1600*580 Board: White HMR 16mm Edging: White 1mm include 4 mirror 390*2000 include Hanging Rails push to open doors Shoes Shelf: 2300*1450*300 Board: White HMR 16mm Edging: White 1mm include 7 Shelves Laundry: 2@ cabinet: 800*850*300 Board: White HMR 16mm Edging: White 1mm Include 2 Shelves Rooms: wardrobe with mirror Door: full package for each room Board: White HMR 16mm Edging: White 1mm include 2 mirror doors and Rail include Hanging Rails include 5 drawers for each room

Need to get cabinet doors and cabinets made under bench top in laundry room. Provide cost for install, I can but material from Bunnings.

Need a fix for my 3 kitchen drawers. They are bit misaligned and loose. I tried to apply a fix but that did not help. 1 photo is with the fix that I applied & the other photo is a good part. Any materials will be paid seperately

Hi, I’m looking for someone who can build a feature wall with a built-in fireplace. Preferably someone with a carpentry licence. There are two walls in the house that need to be done. You are more than welcome to visit the site and take measurement if possible.

Hi, I’m looking for someone who can build a feature wall with a built-in fireplace. Preferably someone with a carpentry licence. There are two walls in the house that need to be done. You are more than welcome to visit the site and take measurement if possible.

Extend out bottom step approximately 530mm to make a landing including bottom step of 750mm wide. Current step is currently 1700mm wide by approx 220mm deep. Want to make a landing so total landing including step is 1700mm X 750mm. This landing won't be a permanent feature so we don't need it to be painted or sanded. It will sit on top of the concrete but does not need to be attached. It needs to be freestanding. Can use treated pine for example from Bunnings (see attached) to keep cost down

I would like to replace my existing manhole in my garage with a larger opening and drop down attic ladder. Ceiling height 2600 Prefer aluminium ladder Please quote for full supply and install including framing.

Single door shaving cabinet installation on porcelain wall tile

Need someone to build a timber garden box around an established tree in my front yard. I will remove the broken pot and prepare the area beforehand. I’m looking for a neat, strong timber box to cover exposed roots and improve the look of the garden. The design should allow drainage and leave space around the trunk so the tree can continue to grow. Open to suggestions on materials (treated pine or similar). Please include all materials and labour in your quote. I’m flexible on timing and can do weekdays if that helps. Located in Castle Hill.

Hi there • Title: Repair stained Timber by oven cleaner • Description: I need someone handyman to help with some stained timber on the kitchen floor • Current Status: The timber is currently got stained Oven cleaner wet towel timber small area as seen on photos i need someone handyman to repair floor

Rotting in timber needs to be replaced in 2 spots as pictured. Scaffolding will be supplied. Please quote for labour and materials only.

6m x 2m deck, second story There is a front edge section on both sides that would need sanded and sealed too which isn’t included in the above measurements. There is a large pot plant that you’d ideally work around (move it based on the section you are working in) or help us lift out of the way. I’d easily move the smaller pot plants.

I want handyman He know skirting

The dishwasher is tilted because of the cabinet. we need someone to fix it.

Own tools, Ute and experience in decking

16sqm of Merbau to nail down. All materials onsiye

Hi, I’m looking for professional cleaning and staining of two outdoor decks at my home: 1. Main deck: approx. 21 m × 5 m (about 105 m², width varies slightly). 2. Smaller deck: approx. 2.5 m × 3.5 m (about 9 m²). Total area is roughly 114 m². The decks are weathered and have some discoloration (see photos attached). I would like: • Full clean and preparation (deck wash/brightener). • Light sanding if required. • 2 coats of high-quality decking stain/oil (e.g., Intergrain, Cabot’s, or equivalent). Please include in your quote: • Labour cost • Materials (cleaner + stain/oil) • Estimated timeframe to complete