Find a reliable appliance technician in Sydney

Hi, I need someone to help install a slide-out rangehood. I already have the required screws and parts. The issue is that the existing holes in the cabinet do not line up with the new slide-out rangehood, so new holes need to be drilled into the cabinet board for proper installation. The rangehood will be used in recirculation mode, so no ducting/exhaust pipe connection is required. Please bring tools for drilling and installation. Thank you.

I have inherited a second hand washing machine but some parts are missing, and I’m not sure how to install it. Machine in very good condition otherwise. Seeking an Airtasker to advise on installation and tell me the parts it needs. The machine is Fisher & Paykel 9kg frontloader

Looking for a qualified plumber to replace a leaking hot water pipe (see attached photos). The section needing replacement is approximately 1–1.2 metres in length. Access is straightforward, lower section, under the sink. Please bring necessary tools and materials. The final price to include the work + pipe + other materials needed

Thoroughly clean the internals of a washing machine.

I'm looking for a certified Renai Product Specialist to look into the issue I have for my Rinnai Avenger 25 gas heater. When I turn it on, it produces a strong plastic burning smell that quickly fills the room, so I have to switch it off immediately. I have already tried the troubleshooting steps recommended by Rinnai, including cleaning the air filter and running the heater at the highest temperature for a period of time. Unfortunately, the burning smell persists.

We need a routine visit to check a status light of an AED as well as replace and dispose of an AED unit. This will be at most a 30 minute job on site.

Bosch series 6 washer / dryer is not drying, as there is no heat

The dryer stopped working, the function still starts and goes through all the cycle but does not heats up

The Rinnai gas heater suddenly stopped igniting. Its like no gas is getting through.

The drain pump filter cap is not dislodging and I don’t have the screwdriver attachment to take off the bottom panel to dislodge the cap manually.

Washing Machine & Heat Pump Dryer Installation Hi, I need a handyman/appliance installer to complete the setup of a Bosch washing machine and heat pump dryer in my apartment laundry. Tasks: • Connect Bosch washing machine to existing water supply • Connect washing machine drain hose to sink waste pipe • Install suitable drainage connection/spigot into existing sink waste pipe (pictured) • Secure drain hose with appropriate clamp/fittings • Test washing machine for leaks and correct drainage Dryer: • Connect the heat pump dryer’s continuous drain hose so water drains automatically • The dryer water collection tank is difficult/impossible to access due to the tight cabinet space, so I would like the dryer set up for direct drainage instead • Test dryer drainage setup to ensure it works correctly Please bring any tools and any small fittings/clamps required for installation. Please review the attached photo and confirm if any additional parts are required before attending. Looking for someone experienced with appliance installation, washing machines, dryers, or basic plumbing. Location: Rushcutters Bay Flexible on timing.

Looking for a licensed plumber quote to install plumbing and waste for a washing machine in my apartment in Potts Point. The washing machine is currently only sitting in the lounge room and is not connected to any plumbing. Scope of work: Extend existing kitchen water supply and waste plumbing. Run the plumbing through the wall from the kitchen area into the lounge room. Position the washing machine on the right-hand side of the fireplace. Install the required washing machine water connection and waste outlet. Advise on the best concealed route before cabinetry/joinery is installed. Ensure the work is suitable for an older apartment building. Photos and floor plan can be provided. Licensed and insured plumber only please. Location: Potts Point NSW

I got a Smeg dishwasher, the gasket around the door has been wearing off and I already got the new parts , but I need someone to install them. There is also a wooden part beneath the dishwasher that had been taken off , I need to reinstall that too, I upload the photos ( I have the wood panel that is supposed to be installed there) Replacing the gasket is a must, but if you can do the wood panel too, that’d be perfect Feel free to give offers for both or just the gasket I prefer to do this by this Friday

I have an old integrated kitchen range-hood and I need someone to take it out and install a new one in. I have already bought it.

We have one switch which controls the bathroom extractor fan and also the laundry cupboard light. The extractor fan works, but the light doesn’t we have replaced the bulb which has not helped. Could be a faulty switch that needs replacing. Regarding the oven bulb, sometimes the light works and sometimes it doesn’t.

We have a gas leak from a pipe connection i to our meter. The meter is brand new.

Hi, I’m looking for someone experienced with Fisher & Paykel DishDrawer dishwashers to diagnose and repair my current unit. Model: Fisher & Paykel DD60SDFX9 Product code: 81215-C Serial: NHG279757 Issue: the dishwasher is not draining properly. There is standing water at the bottom, and when powered on it makes a very loud whirring/fan-like noise. I’ve already cleaned and checked the filter/pump area multiple times and can’t see any obvious blockage. Possible issue seems to be either: * blocked drain path / hose / sink connection * jammed or failed drain pump / rotor / impeller * possible flood sensor / leak fault state I’m looking for someone who can: 1. Diagnose the issue properly 2. Check the drain hose, sink connection and pump/rotor area 3. Confirm whether it needs a drain pump/rotor replacement or another part 4. Repair it if possible, ideally on the same visit if parts are available Please only offer if you have experience with Fisher & Paykel DishDrawers or similar dishwasher repairs. It would be great if you can mention whether you can source parts, and your availability. Location: Kings Cross, Sydney Timing: as soon as possible / flexible

Dishwasher is leaking from the front, sometimes it gives the E4 code, nothing was shown this time. Looking for someone to diagnose and repair the problem, as well as check for water damage under/behind the dishwasher, which might include pulling it out and re-installing after.

1 of my gas stove burners isn't working. The flame lights wildly for a brief moment before stopping. Address is in Surry Hills, Sydney

I have a washing machine that was installed and forgot to take the transit bolts out of. The unit is approx 70 kg and will need to be lifted straight upward about 1.5m to get them out.