Find a reliable appliance technician in Brisbane

Hi guys I have an under bench fridge that doesn’t get low enough temperature. I’ve cleaned the filter/fins and it worked better for a small amount of time now it’s back to this. It may need a deeper clean but I can’t get in there. If you can do fridge seals too that’s a bonus as they need doing too.

We're looking for an experienced, licensed plumber to prepare the plumbing connections for a commercial coffee machine being installed in our office. Coffee machine: Boxer 2 Group (15AMP) The coffee machine hasn't arrived yet, so we're looking to have the necessary plumbing prepared ahead of delivery. Scope of work: Assess the existing plumbing and proposed machine location Install or prepare a suitable cold water connection with isolation valve Install or prepare the necessary wastewater drainage Advise on water filtration requirements and any additional fittings needed Ensure the plumbing is ready for the coffee machine to be connected once delivered Ideally looking for someone with experience installing plumbing for commercial espresso machines. Please let us know your availability, experience with similar installations and whether you'd need to inspect the site before providing a quote. Photo of the proposed installation area and plumbing situation attached.

Washing machine to hookup - fittings included.

Need to disconnect current gas stove and replace with new one swap position of gas flat grill

The door seal gasket for my Samsung washing machine needs to be replaced. The machine’s model is WW75J54E0IW/SA.

Our new oven requires more space. Current wooden panel (cleats) need to be taken out and replaced smaller piece or cut down to size. See photos.

Overall size: about 75cm wide x 40cm tall x 30cm deep Base: 75cm x 30cm, 19–25mm thick timber Uprights (x2): 70x45mm pine, 38cm tall Top rail: 70x45mm pine, 64cm long Inside gap between uprights: 55cm Tubes (x3): 90mm PVC pipe, 25cm long Treat holes: 6–10 per tube, mix of 15mm, 20mm and 25mm End caps: 90mm, one removable per tube for refilling Axle: 20mm metal rod or hardwood dowel, about 64cm long, set 17cm above the base Axle hole through each tube: 22mm, drilled through the centre (12.5cm from each end) so it spins freely Spacers: short pieces of PVC conduit over the axle between the tubes, about 5cm gap between each tube and between the tubes and uprights Clearance: at least 4cm between the tube and the base, and between the tube and the top rail, when it spins Hold off paint, and don't put zoo writing on it

I need someone to come have a look at the fridge as it’s not cooling anything. May need a new part. Looking for fridge specialist

Water not draining properly, needing help to remove cap to clean filter, its very hard to undo, may be stuck closed. Please help!

Fisher and paykel 2-drawer dishwasher, top drawer not draining. Need it fixed

I need to get someone to fault find on my LG top load washing machine. it is currently not draining into the discharge drain during the rinse / spin cycle. It is draining onto the floor from the bottom of the machine. The drain and pipes have been cleaned and tightened. Once fault is identified, quote on repair.

Looking for an appropriately qualified/licensed appliance repairer or gas fitter to attend a short-term rental property in Windsor, Brisbane to diagnose and repair a gas cooktop ignition issue. Issue: - Gas is flowing to the burners normally - Burners are not electronically sparking/igniting - Guests can currently light the burners manually, but we need the ignition repaired - Make/model can be provided once confirmed We would like someone to attend as soon as possible this week, diagnose the fault and repair it where possible during the same attendance. Potential issue may relate to the ignition system, spark module, electrode or microswitch, however this will need to be professionally diagnosed. Please include in your offer: - Call-out/diagnostic fee - Your availability - Relevant licence/qualifications - Whether you can supply common replacement parts if required Please provide photos/details of the fault and completed repair for our property records.

We have a washing machine inlet that is leaking.

The rubber door seal (door boot/gasket) on my front loader washing machine has come off, along with the wire spring band that holds it in place. Nothing looks torn - it just needs to be put back on properly and the spring refitted. This video shows the kind of job: https://www.youtube.com/watch?v=l3KDqvOxemQ The rubber door seal (door boot/gasket) on my front loader washing machine has come off, along with the wire spring band that holds it in place. It should be repairable - it needs to be put back on properly and the spring refitted. This video shows the kind of job: https://www.youtube.com/watch?v=l3KDqvOxemQ If the seal or spring turns out to be damaged, let me know before buying any parts.f the seal or spring turns out to be damaged, let me know before buying any parts.

Looking for an electrician to install a new GPO below new laundry bench for washing machine. Current GPO to remain as shown in picture if possible.

Remove single draw Fisher & Paykel dishwasher and replace with another one

As it says on the headline. Can assist holding etc for IKEA tv stand. Needs to be this afternoon

I have a Bosch washing machine that is showing error codes E35 and now E30-10. I’ve checked the pump/filter and there doesn’t appear to be a blockage. I was able to run a drain cycle, but it finished with E30-10. I also manually drained some water, and some water got underneath the machine. I need the machine assessed and repaired,

My washing machine is having trouble draining. It stops with 18 mins left and comes up with an error E13.