Hire trusted experts for dishwasher repairs in Central London

Our dishwasher hasn't worked for months. It turns on and seems fine from an electronic perspective, but it won't run a proper cycle and makes a constant gurgling noise, so perhaps there is something wrong with the drainage.

Dishwasher is not draining propoerly, and control panel is glitchy. Sometimes it lets you choose a setting and runs normally, but most of the time it rejects and glitches when you choose a mode, and so it’s hard to get started

Dishwasher fill up non stop and overflow

The dishwasher is not working , the brand is "Bosch", less than 3 years old.

Cupboard removal and dishwasher to be fitted in that space. Will need to get cupboard space looked at before I order the correct dishwasher for it to be fitted

I need a plumber to look at what is going on with my sink and dishwasher. The sink doesnt drain properly and water comes up into the sink when I run the dish washer.

Drill holes in bathroom tiles to attach a clock & some electrical work installing 2 bedside lights on wall & fixing a light fitting on a hallway ceiling also my Dishwasher not working (needs fixing)

Fitted corner cupboard, needs disassembling to fit slim dishwasher, dishwasher needs plumbing in and hole drilled through cabinet to fit plug.

The plinth on top of dishwasher can be removed because the dishwasher needs to be removed.

Need dishwasher installed however need one of the cupboards to get taken out to install it - Have attached pictures for your reference! :)

Originally posted as "Fitted dishwasher is working but it has been installed with the feet being too short and not screwed to the adjacent cabinets." I've done some further looking at this today and I've adjusted the feet so that the door panel is in line with the adjacent doors as you can see in the second photo. However, as you can see in the third photo, there is a ~2.5cm gap between the top of the dishwasher and the bottom of the worktop. So what I think needs doing is that the door panel needs removing, and the dishwasher feet length increased by ~2.5cm so that the dishwasher sits snug underneath the bottom side of the worktop. Then the panel needs refitting ~2.5cm lower on the dishwasher door so that it still sits in line with the other cabinets. Then finally the dishwasher needs screwing to the adjacent cabinets. Unfortunately I don't have the original screws, and I think the cabinet is damaged where one screw was originally fitted, but as this was 2.5cm from where it should be, that might not be a problem. Would you be able to requote on this basis? And do let me know whether you think I've understood the issue correctly or not.

Bosch integrated dishwasher with an error code such as E:02

My dishwasher has stopped draining properly and therefore will not run after about 5 minutes into the cycle. Secondly, the hinges on the door need either tightening or replacing because the door just free falls down if you let go of it, whereas before it would smoothly glide down. It has become a bit of a safely hazzard to be honest as it can hit your leg if you are not careful.

Hi, I’m looking for a qualified plumber to correctly connect my table-top dishwasher under the kitchen sink. At the moment: • The dishwasher water inlet hose is connected via the tap • The waste hose is too long and currently sits in the sink What I need: • Properly connect the dishwasher water supply to the same cold-water supply as the washing machine, using correct fittings • Tidy, shorten, or reroute the dishwasher waste hose and connect it neatly to the correct waste outlet under the sink • Ensure hoses are not under strain • Test the dishwasher and check for leaks Important notes: • Dishwasher and washing machine will remain in their current positions • Professional plumbing work only (no temporary or DIY solutions) • Happy for the plumber to supply any small fittings required • Please bring your own tools Dishwasher: electriQ XL Mini Table Top Dishwasher (Model EQDWTTXL) Photos of the current setup are attached. Budget: £50 Thank you.

The dishwasher is tripping the RCD. Likely need a new seal or diagnostic.

Integrated oven and dishwasher have both lost power. Fridge and washing machine on the same switch panel still work. MCBs unit appear normal. Need electrician to diagnose the issue.

Integrated dishwasher front panel is loose so dishwasher wont open fully. Need to fasten it back on. Thank you!

Twin sinks blocked. Dishwasher not working

My dishwasher is causing the kitchen circuit breaker to trip. When the dishwasher is turned on, the circuit trips almost immediately. After switching off the dishwasher at the wall, the circuit breaker can be reset and works normally. This suggests there may be an electrical fault within the dishwasher (possibly heating element, wiring, or internal component). I need a qualified appliance technician or electrician to: • Diagnose the cause of the fault • Confirm whether it can be repaired safely • Provide repair if possible, or advise if replacement is required

The dishwasher starts but then makes a humming/buzzing sound and stops mid-cycle. The control panel shows a water/tap warning light, indicating a drainage or water flow issue. Likely causes are a blocked filter or drain pump, or debris stuck in the pump impeller. The filter and sump area may need removing and cleaning, and the drain pump checked for obstructions. Reset has been attempted but issue persists.