Find a professional internal door contractor in London

Inspect faulty door latch and either fix it or advise if a new latch is needed and then replace once the new part has arrived

internal door fitted to a new door

I’m looking for someone to refresh an existing internal basement door, approx. 1920 x 690mm. The door needs: * Removing from hinges * Sanding/prep * Filling any chips, cracks or imperfections * Priming where needed * 2 coats of paint * Fitting new handle/ironmongery * Rehanging and adjusting so it closes properly I’ll supply the paint and new hardware. Please bring your own tools, sanding equipment, filler and general prep materials.

I want a new internal door fitted

I need one internal door shortening. I got a new carpet recently and the door no longer clears the floor. It just needs a slight trim. The door has been removed so would want it then putting back on the hinges.

Measurement of current doors below. Need advice on where to buy new doors from so that they are all the same style. 198x72 - Bedroom 1 196-72 - Bedroom 2 202.5-67 - Bathroom x 2 203x72 - Living room 199x76 - Office 203-72 Kitchen

To fit a night latch to an internal door and to fit a handle on another door

I'm looking for someone to hang an internal door to our utility room. The door and all necessary hardware will be supplied. The door frame has not had a door on it previously so will need door jams fitted. Painting afterwards is not required. The door frame is 760mm wide. Please see attached photographs for more details. Happy to answer any questions.

4x internal doors need shaving down after carpet has been laid. Suggested 15-20mm

Fit 2 internal doors - have all fittings

I have 7 internal doors. Several of them don't close properly, and some are quite noisy when opening/ closing. I need an experienced handyman/ door specialist to inspect all 7 doors and fix/ adjust them as far as reasonably possible without replacing the doors themselves. What I need: - Inspect all doors, hinges, frames, latches and strike/ keep plates - Identify why some doors aren't closing properly - Adjust hinges, door alignment, latches and/ or keeps as necessary - Lubricate mechanisms where appropriate - Make the doors close properly and smoothly, with minimal force - Reduce the noise from the doors closing as much as reasonably possible. - Check whether the existing mortice locks/ latches are worn and whether they need adjustment or replacement - Advise me whether replacing the existing handles would make any meaningful difference Important: I don't want the doors themselves replaced. Minor adjustments, hinge/ keep adjustments, lubrication and reasonable minor repairs are fine. Please discuss with me before carrying out any significant carpentry or replacing lock mechanisms. I would ideally like the inspection and the necessary adjustment/ repair work to be completed during the same visit. Please only apply if you have experience with internal doors, mortice locks/ latches and door alignment, and can diagnose why doors aren't closing properly rather than simply replacing the handles.

Heavy glazed internal timber door has come off due to failed/damaged hinges. Door itself is fine. Looking for an experienced carpenter/joiner to repair/reinforce the hinge fixing points, supply suitable hinges and rehang/align the existing door.

Remove existing & fit 9 internal doors including door furniture

I'm looking to replace 3 internal doors

I need to replace 7 internal doors

I have 3x internal wooden doors that do not latch and close properly. These doors do not have locks on them so it should be a simple fix of potentially replacing with longer screws in the hinges etc. Please give a quote for labour only including how long you think it will take.

Fit 3 internal doors and change a radiator

A small job for an experienced carpenter/joiner to hang a new internal door. The door has already been planed to size and fits the opening, so won’t need any resizing or trimming. I just need someone to: * Fit and recess the hinges into the door and frame. * Hang the door so it is straight, flush and operates smoothly with even gaps. * Fit a pull handle to the door (pull handle only – no latch or lock mechanism). The frame is already in place, and the door is ready to be hung. I’ve attached a photo of the opening. Tools: * I have tools available, including a planer and chisels. * Ideally, you’ll bring your own professional tools. Parking: * I’ll cover the cost of parking. Looking for: * Someone with experience hanging internal doors. * Attention to detail – I’d like the door aligned properly with clean hinge recesses and a good finish. Please let me know your experience and, if possible, include photos of similar carpentry work you’ve completed.

Hi all! I have a door, unsure wether it is the right size so will need to maybe be cut down. I have hinges and the handle needed.

Job is to swap back and re-hang the internal doors replacing the current fire doors. Including opening up a stud wall and putting double doors in the dining room. The doors are labelled as to which one goes in each room, so they should fit okay. These are the old doors originally present. So each of the doors will need to be re-fitted and all the doorways made good. Just as a note, some of the doorstops may need to be changed. With a few holes being filled where the door closers were. I would expect a job to take two days for someone that knows what they’re doing. Price is for labour happy to pay for any materials required. You’re welcome to use either the hinges fitted to the doors or the hinges fitted to the fire doors. There’s approximately nine doors, see photo