Find an experienced door installer near you

Need to plaster this existing dog door and then put a new cat door inside to prevent pests and cold air from coming in. Plastering dimensions: 28cm*49cm Cat door to install (I will supply) :https://www.bunnings.com.au/hakuna-pets-large-cat-flap_p3962390

I need to replace my bathroom door lock , I got lock from Bunnings need to replace it

I need a qualified technician/handyman to replace the rubber door seal on a commercial fridge in my cafe located in Waterloo, NSW. The current seal is worn and coming loose, which is affecting the door closure and temperature efficiency. Scope of works: • Inspect existing fridge door seal • Supply and install correct replacement gasket (commercial grade) • Ensure door seals tightly and fridge maintains proper temperature • Remove and dispose Two fridges, see attached photos. Must be able to attend between the hours of 6am to 4pm

Remove hallway carpet from front door down to back bedrooms. And install 4 nice doorway edges at the joins to the rooms.

I have a tilt panel door 5000 x 2100 I need installed have all brackets for mounting and motor just needing it installed.

I need a door installed for my walk in robe.

I need a space framed out and timber door installed.

Replace the Door Gasket/Seal of an LG FL Washing Machine I bought a new genuine Door Gasket/Seal LG Washer/Dryer Model: WD 141 30 FD6 Serial No. 302 KWJU 35620 Please provide a quote and a date. West Pennant Hills 2125

I have taken the old door handle off. Need the new handle put on. The holes for bolts for the previous handle are vertical, but this handle needs holes aligned horizontally. Also the hole for the latch needs to be a bit bigger to accommodate the new latch.

Need theatre cavity doors replaced. Size 2.4m H X 820W.

Drill holes and install door handles x3

2 bedroom doors and 4 wardrobe doors need to be replaced. Also fix the broken plaster board. Looking for a carpenter to provide the estimate. I will supply all materials. Only labour needed. Location: Loganlea

Remove and replace old door jam

Need door handle replaced Need to make sure it locks and closes / opens properly. We will get a replacement handle tomorrow. Need done before Monday Thanks

I need 8 door handles replaced in our home. I will supply handles. See photos for the type.

Set a small section of gyprock that has been installed to close the gap between a new door frame and the ceiling. Front and back of the door frame need setting, and the back side needs a new cornice piece to match the existing cornice

We have a door with no handle , we would like to install a door handle in the door.

I’m looking for an experienced carpenter/cabinet maker to complete the final installation of two custom solid Tasmanian oak sliding wardrobe doors. This is a top-hung system (not bottom-rolling), so please read carefully. Overview - Qty: 2 sliding doors - Material: Solid Tasmanian oak (raw timber – no finishing required) - Size (each): 2510mm H x 1170mm W x 30mm T - Weight: Heavy solid timber What’s already done (~90% complete) - Top track is fully installed and fixed - Doors are already built to size - Opening/walls/floor are square - Flat timber floor (no slope) - Wardrobe carcass is complete Key clarification (important) This is a top-hung sliding door system with a low-profile floor guide, NOT a bottom roller/bottom track system. - Doors hang entirely from the existing top track - Bottom only needs a small guide to prevent lateral movement - Total clearance available: ~30mm (sufficient for this system) Bottom guide details - Low-profile plastic/nylon floor guide (shown in photos) Requires: - Routing a single narrow vertical groove into the bottom edge of each door - Fixing the guide to the floor - No bottom rollers, no full bottom track, no 50–80mm clearance required Scope of work - Route narrow groove in bottom of both doors - Supply & install suitable low-profile floor guide (or use supplied one if suitable) - Hang both doors on existing top track - Align/adjust so doors are plumb, stable, and slide smoothly - Install stops if required - Clean, professional finish Ideal person - Carpenter or cabinet maker - Experience with top-hung sliding doors - Confident routing grooves in solid timber - High attention to detail Photos provided: top track/hardware, floor guide, installation diagram, and wardrobe setup. Please quote including labour + any small hardware required. This should be a straightforward finishing job for someone experienced with this system.

Hang new door (photo below) and install door hardware (handle with lock) Patch up door frame.

Install handle and lock to external door.