Find experienced local carpenters in Glebe NSW

I’m looking for a carpenter to build a 2 person sauna. I have the plans and all materials. Likely take 2-3 days. Please bid on a day rate.

I have a stainless steel fridge that had magnets on it. When I’ve pulled the magnets off, some have left a rust like look on the fridge from the magnet itself rusting. I would like some experienced in removing this without damaging the fridge or fridge varnish. If this is you, I’d love to hear from you.

Replace Outdoor Timber Bench/Box Top – 3m × 450mm Looking for a carpenter/handyman to remove and replace the existing weathered timber boards shown in the photo. Approximate dimensions: 3000mm long × 450mm wide. Looking for a like-for-like replacement using suitable outdoor decking timber, including removal/disposal of existing boards, supply of new timber, installation and exterior oil/stain. Existing concrete/rendered base is to remain. Please quote all-inclusive supply and installation.

Carpentry. Replace a 100mm dia. Pine log pergola beam that has rotted and split in half. The pine log is approx. 3.5m long and notched at each end and fixed to supports. We will place this inside of the polycarbonate roof so the beam doesn’t rot out again.

IKEA METOD wardrobe rail + cabinet installation — Glebe Looking for someone experienced with IKEA/METOD cabinetry to finish installing these wardrobes. The cabinets are already assembled and positioned, and I’ve already measured and cut the suspension rails for both areas. I just need: - Suspension rails levelled and securely drilled into the solid brick/masonry walls - Cabinets hung on the rails, flush and level - Cabinets clamped together and screwed/fixed neatly to each other - Final alignment checked so everything is straight and ready for doors/fronts There are 4 tall cabinets in the bedroom and 3 tall cabinets in the hallway. I already have: - Masonry drill - Masonry drill bit - packing/shims - 6 mm × 75 mm masonry hex screws - Heavy-duty clamps - Stud finder if useful Would prefer someone experienced with fixing cabinetry into masonry and who can do their usual checks before drilling. Location: Glebe, Sydney Please bring any other installation/levelling tools you normally use. Photos show the cabinets and installation areas.

IKEA METOD wardrobe rail + cabinet installation — Glebe Looking for someone experienced with IKEA/METOD cabinetry to finish installing these wardrobes. The cabinets are already assembled and positioned, and I’ve already measured and cut the suspension rails for both areas. I just need: - Suspension rails levelled and securely drilled into the solid brick/masonry walls - Cabinets hung on the rails, flush and level - Cabinets clamped together and screwed/fixed neatly to each other - Final alignment checked so everything is straight and ready for doors/fronts There are 4 tall cabinets (200cm tall)in the bedroom and 3 tall cabinets (200cm tall)in the hallway. I already have: - Masonry drill - Masonry drill bit - 6 mm × 75 mm masonry hex screws - Heavy-duty clamps - Stud finder if useful Would prefer someone experienced with fixing cabinetry into masonry and who can do their usual checks before drilling. Location: Glebe, Sydney Please bring any other installation/levelling tools you normally use. Photos show the cabinets and installation areas.

Meet me at my place with a hand held sander and some wooden floor varnish, sand down 2x floodboards and coat with varnish.

2 cabinet doors not working. One does not close. One has come off hinges

Need a carpenter to put up a side fence. Wood supplied.

I need 2 jobs done 1. Build and install a cabinet to hide my meter box (rough dimensions: 900 x 600 x 250) 2. Build or pick up wood panels from bunnings and install outdoor wall panels to existing fence. (Rough dimensions: 3.5m x 2m)

I need the timber lengths in the picture cut into thirds (or so). I need the bike lock in the picture cut as the lock and key are broken.

I need a handyman / cabinet maker to modify an existing kitchen cabinet to install a washing machine under the benchtop and place a benchtop dishwasher above it/or a narrow dishwash on its left (on the carpet as per the picture). Both appliances will be supplied by me. Water inlet and drain have already been installed. Existing setup • Drawer stack approx. 60 cm wide located to the left of the kitchen sink • Standard kitchen benchtop above • Water inlet and drain already installed inside the cabinet • Wall power socket on the right wall above the benchtop (to the right of the stove) will be used to power the appliances Scope of work 1. Remove drawers Remove the existing drawers and runners. Remove or modify internal cabinet panels if needed while keeping surrounding cabinetry and benchtop intact. 2. Prepare cavity Convert the cabinet space into an open cavity suitable for a 60 cm washing machine. Ensure enough clearance for hoses and ventilation and make sure the base is level and stable. 3. Appliance connection Connect the washing machine to the existing water inlet and drain. 4. Electrical Appliances will use the existing wall socket visible on the right wall above the benchtop. 5. Finishing Trim exposed cabinet edges if needed. Ensure appliances are stable and functioning and clean the work area after completion. Measurements • Cabinet width approx. 60 cm • Photo available for reference

Create 35mm cabinet contemporary for shoes

The old timber counter now sits under the marble countertop and needs to be cut out for our fridge to have space to fit under bench. The area is approximately 1200x700. Job is in a cafe and will need to be done after 3pm.

Seeking someone to build a custom bench in solid timber (Ash/blackbutt/spotted gum) NOT plywood. Dimension of the bench should be: Bench top dimensions: 50cm depth x 80cm length x 90cm height. Legs: solid 'waterfall' timber legs on the end of each length. See pictures for creative direction.

Interior plywood kitchen benchtops and external timber breakfast bench require resurfacing and refinishing. See photos.

Repair replace cracked portion of timber frame on French door and realign to track so door is functional

Hi, I would like to install the stainless steel splashback wall into the commercial kitchen. Around 2400mm X 2000mm Please quote the price with the splashback since I don't have it. Shop in Glebe 2037

I need to replace to damaged timer doors. i have the doors which will need to be trimmed to size and the existing door hardware transferred over.

I want to create some open cabinets that go into my pantry. I've included all the measurements in the first photo but its roughly: 208cm long, 35cm deep, 87cm tall on the side and 105cm, 50cm deep, 87cm tall at the back (where you can currently see small shelves. I'm looking to just get it done in plywood but am open to ideas and happy to use flatpacks/prefab if that's a lot easier/cheaper. Not looking for any fancy benchtop as will not be using it for chopping, more for storing appliances etc.